Bottom View, SW Settings, SW1-8, SW2-7, SW3-6 | Aspire Digital 1520

SW Settings

Bottom View

1	CN11	Wireless LAN Card Connector	5	U93	FIR Port
2	CN12	Modem Board Connector	6	DM1	DIMM Socket 1
3	CN10	Modem Cable Connector	7	DM2	DIMM Socket 2
4	SKT2	IEEE 1394 Port	8	BAT1	DC Charger Board Connector

SW Settings

	SW1-8	SW2-7	SW3-6

Chkpw	ON	X
Enable

Bootblock	X	ON
Enable

99

Chapter 5

Image 108

Aspire Digital 1520, 1360 manual Bottom View, SW Settings, SW1-8, SW2-7, SW3-6

Contents

Service Guide Aspire 1360/1520 Series Revision History Copyright Disclaimer Conventions Screen messages Preface Page Table of Contents Chapter 3 Machine Disassembly and ReplacementChapter 1 System Introduction Chapter 2 System Utilities Chapter 4 Troubleshooting Page Features System IntroductionChapter Performance Expansion Human-centric designI/O Ports EGRET Block Diagram DiagramL1 Signal L3 Signal Board Layout Top View Bottom View DC Charger Board Connector Panel Front View Left view Right View Rear Panel Icon Bottom View Indicators Keyboard Special keysLock keys Embedded numeric keypad Desired accessNum lock on Num lock off Windows keys Hot Keys Hot Key 1. Click on Start, Control Panel 2. Double-click on Regional and Language Options Launch Keys Hardware Specifications and Configurations BIOSBluetooth Controller/Chipset Does this System Board Major Chips Second Level Cache System MemoryMemory Combinations LAN Interface Modem Interface Hard Disk Drive Interface CD-ROM Interface DVD-ROM Interface Combo Drive Interface Soft eject with emergency eject hole DVD Dual Interface CD-R Low Speed CD-RWHigh Speed CD-RW Ultra Speed CD-RW VGA Display Resolution Audio InterfaceVideo Interface Source image in the frame buffer LCD Display Resolution CRT Display ResolutionsVideo Memory Parallel Port Battery USB PortPCMCIA Port Keyboard AC Adapter Power Management Environmental Requirements Mechanical Specification Chapter BIOS Setup Utility System UtilitiesBoot Main Navigating the BIOS Utility Information Exit Main InfoSystem Time Chapter Advanced Infrared Port FIRBase I/O address Interrupt Chapter Security BootUser Password is Supervisor Password is Setting a Password Clear or Set Removing a Password Changing a Password Chapter Boot Network Boot+Hard Drive Esc Exit Exit Exit Saving ChangesDiscard Changes Save Changes BIOS Flash Utility Machine Disassembly and Replacement General Information Before You Begin Disassembly Procedure Flowchart Screw List CushionsH*8 for H*6 for Removing the Battery 1. To remove the battery, push the battery release latch2. Then slide the battery out from the machine Removing the Memory Module 1. See “Removing the Battery” on page3. Remove the dimm cover 4. Pop up the memory 5. Then remove the memory Removing the Wireless LAN Board and the Modem Board Removing the Hard Disk Drive Module Disassembling the Hard Disk Drive Module Removing the LCD Module Removing the Middle CoverRemoving the Launch Board Removing the LCD Module Chapter Disassembling the LCD Module Removing the LCD BezelRemoving the Inverter Board 15” LCD Removing the 15” TFT LCD Removing the LCD Brackets Removing the LCD Coaxial Cable Removing the LCD Hinges Removing the RTC Battery Disassembling the Main UnitRemoving the Keyboard Removing the Middle Cover Hook /Fan Installing the Processor Removing the Thermal ModuleRemoving the Processor Removing the Upper Case Assemly Removing the Touchpad Board Removing the Touchpad CableRemoving the VGA Thermal Plate Removing the CPU Heatsink Plate Removing the Second Fan Bracket Removing the ODD Module1 Removing the ODD Module2Removing the HDD Bracket Removing the Main Board Removing the DC Board Removing the I/O Port Bracket Removing the PCMCIA Slot Removing the Speaker Set 13. See “Removing the DC Board” on page System Upgrade Procedure Base Unit to Wireless Unit Troubleshooting Symptoms VerifiedGo To System Check Procedures External Diskette Drive CheckExternal CD-ROM Drive Check Keyboard or Auxiliary Input Device Check Power System Check Memory check Check the Power Adapter Check the Battery Pack Touchpad Check Power-On Self-Test POST Error Message Index of Error Messages Error Code ListError Message List Error Message List No beep, power-on indicator turns off and LCD is POST Code CodeBeeps POST Routine Description 2-1-2-3 Code For Boot Block in Flash ROM Index of Symptom-to-FRU Error Message LCD-Related SymptomsIndicator-Related Symptoms Power-Related Symptoms PCMCIA-Related Symptoms Memory-Related SymptomsSpeaker-Related Symptoms Power Management-Related Symptoms Peripheral-Related Symptoms Keyboard/Touchpad-Related SymptomsModem-Related Symptoms Intermittent Problems Undetermined Problems How to Build NAPP Master Hard Disc Drive CD to Disk Recovery 6. Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till you finish all Recovery CDs 7. Then insert the System CD to the optical drive Disk to Disk Recovery Page 7. Then insert the System CD to the optical drive Chapter Chapter Chapter Jumper and Connector Locations SW Settings SW1-8SW2-7 SW3-6 FRU Field Replaceable Unit List Aspire 1360/1520 Exploded Diagram Aspire Aspire Aspire Chapter Aspire Aspire Chapter Aspire Aspire Chapter Aspire Aspire Chapter Aspire Aspire Chapter Aspire Aspire WIRELESS ANTENNA RIGHT BLACK WIRELESS ANTENNA LEFT GRAY50.A20V1.001 50.A20V1.002 Aspire Chapter Aspire Aspire Chapter Aspire Aspire Chapter Chapter Model Definition and Configuration Appendix AModel Name Definition ODD/Card Test Compatible Components Appendix B Microsoft Windows XP Environment Test Specifications DVD Dual Specifications Appendix B Specifications Appendix B Appendix B Appendix C Online Support Information Appendix C Index Windows XP Environment Test