Chapter, Parameter, Description, Options | Aspire Digital 1360

Manual background

Parameter	Description	Options

DMA channel	Sets a DMA channel for the printer to operate in	DMA3/DMA1
	ECP mode. This parameter is enabled only if Mode
	is set to ECP.

Legacy USB Support	Enables, disables USB interface devices support.	Option: Disabled or Enabled
	(Enable for use with a non-USB aware Operating
	System such as DOS or UNIX).

Chapter 2

38

Image 47

Aspire Digital 1360, 1520 manual Chapter, Parameter, Description, Options

Contents

Aspire 1360/1520 Series Service Guide Revision History Disclaimer Copyright Screen messages Conventions Preface Page Chapter 2 System Utilities Table of ContentsChapter 3 Machine Disassembly and Replacement Chapter 1 System Introduction Chapter 4 Troubleshooting Page Performance FeaturesSystem Introduction Chapter I/O Ports ExpansionHuman-centric design L3 Signal EGRET Block DiagramDiagram L1 Signal Top View Board Layout DC Charger Board Connector Bottom View Front View Panel Left view Right View Icon Rear Panel Description Indicators Lock keys KeyboardSpecial keys Num lock off Embedded numeric keypadDesired access Num lock on Windows keys Hot Key Hot Keys 2. Double-click on Regional and Language Options 1. Click on Start, Control Panel Launch Keys System Board Major Chips Hardware Specifications and ConfigurationsBIOS Bluetooth Controller/Chipset Does this LAN Interface Second Level CacheSystem Memory Memory Combinations Hard Disk Drive Interface Modem Interface DVD-ROM Interface CD-ROM Interface Soft eject with emergency eject hole Combo Drive Interface DVD Dual Interface Ultra Speed CD-RW CD-RLow Speed CD-RW High Speed CD-RW Source image in the frame buffer VGA Display ResolutionAudio Interface Video Interface Parallel Port LCD Display ResolutionCRT Display Resolutions Video Memory Keyboard BatteryUSB Port PCMCIA Port AC Adapter Environmental Requirements Power Management Mechanical Specification Chapter Main BIOS Setup UtilitySystem Utilities Boot Navigating the BIOS Utility Exit Information System Time MainInfo Chapter Interrupt AdvancedInfrared Port FIR Base I/O address Options Supervisor Password is SecurityBoot User Password is Clear or Set Setting a Password Changing a Password Removing a Password Chapter Esc Exit BootNetwork Boot +Hard Drive Discard Changes Save Changes ExitExit Saving Changes BIOS Flash Utility Machine Disassembly and Replacement Before You Begin General Information Disassembly Procedure Flowchart H*6 for Screw ListCushions H*8 for 2. Then slide the battery out from the machine Removing the Battery1. To remove the battery, push the battery release latch 5. Then remove the memory Removing the Memory Module1. See “Removing the Battery” on page 3. Remove the dimm cover 4. Pop up the memory Removing the Wireless LAN Board and the Modem Board Disassembling the Hard Disk Drive Module Removing the Hard Disk Drive Module Removing the Launch Board Removing the LCD ModuleRemoving the Middle Cover Removing the LCD Module Chapter Removing the Inverter Board 15” LCD Disassembling the LCD ModuleRemoving the LCD Bezel Removing the 15” TFT LCD Removing the LCD Coaxial Cable Removing the LCD Brackets Removing the LCD Hinges Removing the Middle Cover Hook /Fan Removing the RTC BatteryDisassembling the Main Unit Removing the Keyboard Removing the Processor Installing the ProcessorRemoving the Thermal Module Removing the Upper Case Assemly Removing the VGA Thermal Plate Removing the Touchpad BoardRemoving the Touchpad Cable Removing the Second Fan Bracket Removing the CPU Heatsink Plate Removing the HDD Bracket Removing the ODD Module1Removing the ODD Module2 Removing the Main Board Removing the I/O Port Bracket Removing the DC Board Removing the Speaker Set Removing the PCMCIA Slot 13. See “Removing the DC Board” on page Base Unit to Wireless Unit System Upgrade Procedure Go To TroubleshootingSymptoms Verified Keyboard or Auxiliary Input Device Check System Check ProceduresExternal Diskette Drive Check External CD-ROM Drive Check Memory check Power System Check Check the Power Adapter Touchpad Check Check the Battery Pack Power-On Self-Test POST Error Message Error Message List Index of Error MessagesError Code List FRU/Action in Sequence No beep, power-on indicator turns off and LCD is POST Routine Description POST CodeCode Beeps 2-1-2-3 POST Routine Description For Boot Block in Flash ROM Power-Related Symptoms Index of Symptom-to-FRU Error MessageLCD-Related Symptoms Indicator-Related Symptoms Power Management-Related Symptoms PCMCIA-Related SymptomsMemory-Related Symptoms Speaker-Related Symptoms Modem-Related Symptoms Peripheral-Related SymptomsKeyboard/Touchpad-Related Symptoms Intermittent Problems Undetermined Problems CD to Disk Recovery How to Build NAPP Master Hard Disc Drive 6. Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till you finish all Recovery CDs 7. Then insert the System CD to the optical drive Disk to Disk Recovery Page Chapter 7. Then insert the System CD to the optical drive Chapter Chapter Jumper and Connector Locations SW3-6 SW SettingsSW1-8 SW2-7 FRU Field Replaceable Unit List Aspire 1360/1520 Exploded Diagram Aspire Aspire Chapter Aspire Aspire Chapter Aspire Aspire Chapter Aspire Aspire Chapter Aspire Aspire Chapter Aspire Aspire Chapter 50.A20V1.002 WIRELESS ANTENNA RIGHT BLACKWIRELESS ANTENNA LEFT GRAY 50.A20V1.001 Chapter Aspire Aspire Chapter Aspire Aspire Chapter Aspire Chapter Model Name Definition Model Definition and ConfigurationAppendix A ODD/Card Appendix B Test Compatible Components Specifications Microsoft Windows XP Environment Test DVD Dual Appendix B Specifications Appendix B Specifications Appendix B Appendix C Online Support Information Appendix C Index Windows XP Environment Test