Asus 8400GSSL1GD3L, 8400GSSL512MD3L 3.9Abnormal Events

4.Click OK button.

If you disable “enable Manual HyperDrive Clock Rate” box, the engine Overclocking rate for HyperDrive is set to the default value.

The default value for each ASUS graphics cards is different.

3.9Abnormal Events

There are three type of abnormal events : unstable voltages, temperature overheat, and fan malfunction. When ASUS SmartDoctor detects an abnormal event, it will display a warning message on the upper-left side of the dialog box.

If you want ASUS SmartDoctor to inform you of abnormal events, enable the alarm settings in the monitor page.

You can check the Enable Overheat protection or Disable Warning When Running 3D games in the setting page to facilitate abnormal event notification.

e3325_vga sw_0829.indb 33			2007.8.29 11:34:03 AM

Contents

Page E3325 Second Edition July Page Abnormal Notices Federal Communications Commission Statement Canadian Department of Communication Statement Safety information Electrical safety Operation safety Macrovision Corporation Product Notice About this guide Conventions used in this guide Where to find more information 1.ASUS Splendid 1.1 System Requirements 1.2Introduction 1.3Launching ASUS Splendid 2.Select ASUS tab > ASUS Splendid to display the following * Set Region The options of Set Region are: All, Left only and Right only * Dynamic Contrast Splendid Mode Table 1.4Limitation 2.ASUS GamerOSD 2.1System Requirements 2.2Enabling ASUS GamerOSD 2.3User Interface 2.3.13D Display Setting Page 2.3.2Video Capturing 2.3.3Screenshots 2.4Using GamerOSD 2.4.1Using 3D Display Function 2.4.2Using Video Capturing Function Page Page Page 2.4.3Using Screenshots Function Page 3.ASUS SmartDoctor 3.1System Requirements 3.2Features 3.3Launching ASUS SmartDoctor 3.4Voltage status 3.5Temperature status 3.6Fan speed status 3.7Engine and memory clock settings 3.8Advanced setup features 3.8.1Settings Monitor Settings Page Page Minimize SmartDoctor at next reboot 3.8.2Monitor Voltage Alarm Settings Temperature Alarm Settings Fan Alarm Settings 3.8.3Fan Control Page Page 3.8.4HyperDrive ASUS HyperDrive GPU temperature mode 4.Click Default to load optimum settings ManualOverclocking rate forHyperDrive Follow the steps below to set the engine Overclocking rate for HyperDrive: Click to enable “Enable Manual Clock Rate” OverClocking Rate for 2.Click OK button on the warning message 3.9Abnormal Events 3.10Information 3.11Terminology Page AGPVDDQ PCIE 4.ASUS VideoSecurity Online 4.1System Requirements 4.2What’s New 4.3Launching ASUS VideoSecurity Video source: changes the Video connector type Set detect region:use mouse to drag a rectangular region you want to detect VideoSecurity Online working modes includes Standby, Watchdog and Tracing WatchDog: Stop 4.4Setup 4.4.1Main Setting the detecting interval parameter To set the detecting interval parameter: 4times/sec. - OR Click Default to set the recommended scan rate Setting the working directory Setting other features Setting the detection region To set the detect region, click the Detect Region option buttons 4.4.2Mode Setting the tracing method To set the tracing method: Stop tracing when user’s press “Stop” 4.4.3Email setting Page Sending Mail Server Mail Address - refers to the sender’s email address Username - refers to your user account name Misc Send All messages MIME encoded - allows support for 5.Click OK to save the configuration or Cancel to abort 4.4.4Record setting 4.4.5Device Page 4.4.6Skype Setting Page figure 1:home PC figure 2: remote side PC 4.5Video Source Video source setting 4.6Set detect region Page Page 4.7Limitations