Asus 8400GSSL1GD3L, 8400GSSL512MD3L PCIE, AGPVDDQ

AGPVDDQ

The working voltage of the AGP bus on the motherboard. The standard VDDQ voltage value depends on the AGP speed running on your system.

NOTE: For some models do not monitor AGPVDDQ value, ASUS SmartDoctor will disable the AGPVDDQ item on the voltage page. ex: V9520 Video Suite and V9560 Video Suite

PCIE 12V

The working voltage of the PCIE bus on the motherboard. The standard voltage value should be around 12V.

NOTE: For some models do not monitor PCIE 12V value, ASUS SmartDoctor will disable the PCIE 12V item on the voltage page. ex EN5900

The information tab displays the Model name, Chip Name, Memory Size, BIOS etc. information of your graphics.

e3325_vga sw_0829.indb 36			2007.8.29 11:34:03 AM

Contents

Page E3325 Second Edition July Page Abnormal Notices Federal Communications Commission Statement Canadian Department of Communication Statement Safety information Electrical safety Operation safety Macrovision Corporation Product Notice About this guide Conventions used in this guide Where to find more information 1.ASUS Splendid 1.1 System Requirements 1.2Introduction 1.3Launching ASUS Splendid 2.Select ASUS tab > ASUS Splendid to display the following * Set Region The options of Set Region are: All, Left only and Right only * Dynamic Contrast Splendid Mode Table 1.4Limitation 2.ASUS GamerOSD 2.1System Requirements 2.2Enabling ASUS GamerOSD 2.3User Interface 2.3.13D Display Setting Page 2.3.2Video Capturing 2.3.3Screenshots 2.4Using GamerOSD 2.4.1Using 3D Display Function 2.4.2Using Video Capturing Function Page Page Page 2.4.3Using Screenshots Function Page 3.ASUS SmartDoctor 3.1System Requirements 3.2Features 3.3Launching ASUS SmartDoctor 3.4Voltage status 3.5Temperature status 3.6Fan speed status 3.7Engine and memory clock settings 3.8Advanced setup features 3.8.1Settings Monitor Settings Page Page Minimize SmartDoctor at next reboot 3.8.2Monitor Voltage Alarm Settings Temperature Alarm Settings Fan Alarm Settings 3.8.3Fan Control Page Page 3.8.4HyperDrive ASUS HyperDrive GPU temperature mode 4.Click Default to load optimum settings ManualOverclocking rate forHyperDrive Follow the steps below to set the engine Overclocking rate for HyperDrive: Click to enable “Enable Manual Clock Rate” OverClocking Rate for 2.Click OK button on the warning message 3.9Abnormal Events 3.10Information 3.11Terminology Page AGPVDDQ PCIE 4.ASUS VideoSecurity Online 4.1System Requirements 4.2What’s New 4.3Launching ASUS VideoSecurity Video source: changes the Video connector type Set detect region:use mouse to drag a rectangular region you want to detect VideoSecurity Online working modes includes Standby, Watchdog and Tracing WatchDog: Stop 4.4Setup 4.4.1Main Setting the detecting interval parameter To set the detecting interval parameter: 4times/sec. - OR Click Default to set the recommended scan rate Setting the working directory Setting other features Setting the detection region To set the detect region, click the Detect Region option buttons 4.4.2Mode Setting the tracing method To set the tracing method: Stop tracing when user’s press “Stop” 4.4.3Email setting Page Sending Mail Server Mail Address - refers to the sender’s email address Username - refers to your user account name Misc Send All messages MIME encoded - allows support for 5.Click OK to save the configuration or Cancel to abort 4.4.4Record setting 4.4.5Device Page 4.4.6Skype Setting Page figure 1:home PC figure 2: remote side PC 4.5Video Source Video source setting 4.6Set detect region Page Page 4.7Limitations