Asus CUBX-E, CUBX-L 40

3. HARDWARE SETUP

(This page was intentionally left blank.)

H/WConnectors

SETUP

40	ASUS CUBX-L/CUBX-E User’s Manual

Contents

CUBX-L ASUS CUBX-L/CUBX-E 1.00 E606 September ASUS CUBX-L/CUBX-EUser’s Manual ASUSTeK COMPUTER INC. (Asia-Pacific) ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) Page Page Page 1.1How This Manual Is Organized 1.2 Item Checklist 2.1.1 Specifications Multi-I/O: Wake-On-LAN Connector: PCI-L101 LAN Card 2.1.2Special Features 2.1.3 Performance Features 2.1.4Intelligence 2.2Motherboard Components 2.2.1Component Locations 3.1CUBX-L/CUBX-EMotherboard Layout 3.2Layout Contents SETUP H/W 3.3Hardware Setup Procedure 3.4Motherboard Settings Motherboard Features Settings (DIP Switches - DSW) 1) JumperFree™ Mode (JEN) setup (see 4.4 Advanced Menu) Setting JEN 2)AGP Bus Frequency Setting (DSW Switch 6) 3)CPU External Frequency Selection (DSW Switches 7-10) 4)CPU Core:BUS Frequency Multiple (DSW Switches 1-4) Manual CPU Settings Set the DIP switches by the Internal speed of your processor as follows: 3.5System Memory (DIMM) 3.5.1 General DIMM Notes 3.5.2Memory Installation Page 3.6Central Processing Unit (CPU) CAUTION H/WSETUP 3.7Expansion Cards 3.7.1 Expansion Card Installation Procedure 3.7.2Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards 3.7.3Accelerated Graphics Port (AGP) 3.8Connectors 3)Universal Serial Bus Ports (Black two 4-pinUSB) 4)Parallel Port Connector (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) NOTE 6)Chassis Intrusion Lead (4-1pin CHASSIS) 7)Floppy Disk Drive Connector (34-1pin FLOPPY) 8)IDE Connectors (40-1pin PRIMARY / SECONDARY IDE) TIP: (40-1pin THIRD / FOURTH IDE) (only on CUBX-E) NOTES: 9)Wake-On-LANConnector (3-pinWOL_CON) IMPORTANT: 4.5.1 Power Up Control 10)Wake-On-RingConnector (2-pinWOR) 11)IDE Activity LED (2-pinIDELED) do not place jumper caps over these pins 13)Infrared Module Connector (5-pinIR) UART2 Use Infrared 4.4.2 I/O Device Configuration) 14)SMBus Connector (5-1pin SMB) 15)USB Headers (10-1pin USB2, 5-1pin USB3A) 16)ATX Power Supply Connector (20-pinblock ATXPWR) 17)Power Supply Thermal Sensor Connector (2-pinblock JTPWR) 18)System Power LED Lead (3-pinPWR.LED) 19)Keyboard Lock Switch Lead (2-pinKEYLOCK) 21)System Message LED Lead (2-pinMSG.LED) 22)System Management Interrupt Lead (2-pinSMI) 23)ATX Power Switch / Soft-OffSwitch Lead (2-pinPWR.SW) Page 3.9Starting Up the First Time Award BIOS Beep Codes 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 4.1.2Updating BIOS Procedures (only when necessary) Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Translation Method Head Sector CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] 4.3.2 Keyboard Features Intel PIIX4E PCIset 4.4Advanced Menu CPU Vcore CPU Level 1 Cache, CPU Level 2 Cache [Enabled] CPU Level 2 Cache ECC Check [Disabled] Processor Serial Number [Disabled] BIOS Update [Enabled] Notes for JumperFree Mode System Hangup Cause for Hangup: Improper CPU Speed Cause for Hangup: Improper CPU Bus/PCI Freq. (MHz) 4.4.1Chip Configuration SDRAM MA Wait State [Normal] Snoop Ahead [Enabled] Host Bus Fast Data Ready [Disabled] 16-bitI/O Recovery Time [1 BUSCLK] 8-bitI/O Recovery Time [1 BUSCLK] 4.4.2I/O Device Configuration Onboard Parallel Port [378H/IRQ7] Parallel Port Mode ECP DMA Select Parallel Port Mode [ECP+EPP] ECP DMA Select [3] 4.4.3PCI Configuration PCI/PNP ISA IRQ Resource Exclusion PCI/PNP ISA DMA Resource Exclusion PCI/PNP ISA UMB Resource Exclusion 4.4.4 Shadow Configuration 4.5Power Menu Video Off Option [Suspend ->Off ] Video Off Method [DPMS OFF] HDD Power Down [Disabled] Suspend-to-RAMCapability [Disabled] Suspend Mode [Disabled] 4.5.1Power Up Control PWR Up On PS2 KB/Mouse [Disabled] Wake Up By Keyboard [Space Bar] PWR Up On PS2 KB/Mouse Automatic Power Up [Disabled] 4.5.2Hardware Monitor 4.6Boot Menu Boot Sequence Other Boot Device Select [INT18 Device (Network)] IMPORTANT: Onboard ATA Device First 4.4.3 PCI Configuration Plug & Play O/S [No] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5.1Install Operating System 5.2 Start Windows 5.3 Installing Drivers and Software 5.3.1 PCI RAID Controller Found 5.3.2Support CD Installation Menu Intel LDCM Administrator Setup (recommended): Intel LDCM Client Setup (recommended): ASUS BIOS Flash Utility for LDCM (recommended): Install ASUS PC Probe Vx.xx (recommended): Install ASUS Update Vx.xx (optional): Page 6.1ASUS PC Probe 6.1.1 Starting ASUS PC Probe 6.1.2Using ASUS PC Probe Settings History Fan Control Information Hard Drives Memory Device Summary DMI Explorer Utility 6.1.3ASUS PC Probe Task Bar Icon 6.2ASUS Update 7.1PCI-L101Fast Ethernet Card 7.1.1 Features 7.1.2 Software Driver Support 7.1.3 Question and Answer 7.2ASUS CIDB Intrusion Detection Module 7.2.1 Using the ASUS CIDB 7.2.2 Setting up the ASUS CIDB 7.2.3 ASUS CIDB Additional Considerations 7.3 Glossary Boot Bus Master IDE Byte (Binary Term) COM Port Concurrent PCI LPT Port (Line Printer Port) MMX OnNow PC100 PCI Bus (Peripheral Component Interconnect Local Bus) ROM (Read Only Memory) SCSI (Small Computer System Interface) SDRAM (Synchronous DRAM) SPD for SDRAM module SSE (Streaming SIMD Extensions) Symbols Page Page Page L8400 Series M8300/8200 Series L7300/7200 Series Page ASUS AR1000 RAID Sub-system ASUS PCI-DA2100/2200Series SCSI RAID Card