Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus P2L97A NOTE, 3.Parallel Printer Connector (25-pinFemale), 4.Serial Port COM1 Connectors (One 9-pinMale)

1 58

Download 58 pages, 727.51 Kb

INSTALLATION .III

Connectors

III.INSTALLATION

3.Parallel Printer Connector (25-pin Female)

You can enable the parallel port and choose the IRQ through “Onboard Parallel Port” in Chipset Features Setup of the BIOS SOFTWARE. NOTE: Serial print- ers must be connected to the serial port.

Parallel (Printer) Port (25-pin Female)

4.Serial Port COM1 Connectors (One 9-pin Male)

One serial port can be used for pointing devices or other serial devices. See “Onboard Serial Port” in Chipset Features Setup of the BIOS SOFTWARE.

Serial Port COM 1 (9-pin Male)

5.Monitor (VGA) Output Connector (One 15-pin Female) This connector is for a VGA-compatible device.

VGA Port (15-pin Female)

24	ASUS P2L97A User’s Manual

Contents

Page USER’S NOTICE Copyright © 1997 ASUSTeK COMPUTER INC. All Rights Reserved Product Name: ASUS P2L97A Manual Revision: ASUSTeK COMPUTER INC Marketing Info Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE V. DESKTOP MANAGEMENT VI. ASUS PCI SCSI Cards FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS P2L97A Motherboard The ASUS P2L97A Motherboard Layout of the ASUS P2L97A Motherboard Jumpers Expansion Slots/Sockets Connectors Board Layout Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 3.CPU Bus Frequency (FS0, FS1, FS2) 4.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Internal External 2.System Memory (DIMM) DIMM Memory Installation Procedures: 3.Central Processing Unit (CPU) The Motherboard As Shipped The ASUS P2L97A is shipped with the attach mount bridges already installed Installing the Pentium II Processor WARNING Mount the Heatsink: Insert the SEC Cartridge: Secure the SEC Cartridge: 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards 5.External Connectors 3.Parallel Printer Connector (25-pinFemale) NOTE 4.Serial Port COM1 Connectors (One 9-pinMale) 7.Floppy Disk Drive Connector (34-1pinFLOPPY) 8.CPU Fan Power Lead (3-pinFAN1) 9.Primary / Secondary IDE Connectors (Two 40-1pinIDE) 10.IDE activity LED (2-pinIDELED) 11.Wake on LAN Connector (3-pinWOL_CON) 12.IrDA-CompliantInfrared Module Connector (5-pinIR) 13.ATX Power Supply Connector (20-pinATXPWR) 14.Message LED Lead (MSG LED) 15.SMI Suspend Switch Lead (SMI) 16.ATX Power Switch / Soft Power Switch (PWR SW) 17.Reset Switch Lead (RESET) 18.System Power LED (PWR LED) Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Features Menu Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Time Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option Auto detection of hard disks on bootup Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) BIOS Features Setup Details of BIOS Features Setup BIOS BIOS Update (Enabled) CPU Fast String (Enabled) Leave on default setting of Enabled for best performance Deturbo Mode (Disabled) Setup PS/2 Mouse Function Control (Auto) PCI/VGA Palette Snoop (Disabled) OS/2 Onboard Memory > 64M (Disabled) MPS 1.4 Support (Disabled) Chipset Features Setup Details of Chipset Features Setup Video Memory Cache Mode (UC) PCI 2.1 Support (Enabled) Memory Hole At 15M–16M(Disabled) DRAM are xx bits wide Data Integrity Mode (Non-ECC) Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Automatic Power Up (Disabled) PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) SYMBIOS SCSI BIOS (Auto) Auto Disabled Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults Symbios SCSI BIOS and Drivers Setting Up the ASUS PCI-SC200& PCI-SC860 Setting the INT Assignment for the ASUS PCI-SC200 Terminator Requirements for SCSI Devices Terminator Settings for the ASUS PCI-SC860 Terminator Settings for the ASUS PCI-SC200 SCSI ID Numbers for SCSI Devices SCSI ID Priority