Asus P4P800S-X 1.8.3 PCI slots, 1.8.4 AGP slot

1.8.3 PCI slots

The PCI slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications.

1.8.4 AGP slot

The Accelerated Graphics Port (AGP) slot that supports AGP 8X/4X (+1.5V) cards. When you buy an AGP card, make sure that you ask for one with +1.5V specification.

Note the notches on the card golden fingers to ensure that they fit the AGP slot on the motherboard.

Install only +1.5V AGP cards.

Keyed for 1.5v

P4P800S-X

P4P800S-X Accelerated Graphics Port (AGP)

If installing the ATi 9500 or 9700 Pro Series VGA cards, use only the card version PN xxx-xxxxx-30or later, for optimum performance and overclocking stability.

1-14	Chapter 1: Product introduction

Contents

Page E1870 Revised Edition January Chapter 1: Product introduction Standard interrupt assignments IRQ assignments for this motherboard Chapter 2: BIOS Information 2.1 Managing and updating your BIOS 2.1.1 Creating a bootable floppy disk 2.1.2 Using AFUDOS to update the BIOS 2.1.3 Using AFUDOS to copy BIOS from PC 2.5.6 Advanced Power Management Configuration Chapter 3: Software support 3.2.1 Running the support CD Federal Communications Commission Statement •This device may not cause harmful interference, and •Reorient or relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help Electrical safety Operation safety Conventions used in this guide Where to find more information Page Page Page Thank you for buying the ASUS® P4P800S-Xmotherboard Check your P4P800S-Xpackage for the following items 1 x UltraDMA 100/66 cable 1 x Floppy disk cable I/O shield Bag of extra jumper caps User Guide Serial ATA solution CrashFree BIOS AGP 8X support USB 2.0 technology 10/100 Mbps LAN support Onboard LED 1.5.1 Motherboard layout 1.5.2 Placement direction 1.5.3 Screw holes 1.6.1 Overview 1.6.2 Installing the CPU 1.7.1 DIMM sockets location 1.7.2Memory configurations Table 1 Memory frequency/CPU FSB synchronization CPU FSB DDR DIMM Type Memory Frequency 800 MHz Table DDR400 Qualified Vendor List (QVL) 1.7.3 Installing a DIMM Standard interrupt assignments 1.8.2 IRQ assignments for this motherboard 1.8.3 PCI slots 1.8.4 AGP slot 1.Clear RTC RAM (CLRTC1) To erase the RTC RAM: 1.Turn OFF the computer and unplug the power cord 3.Plug the power cord and turn ON the computer Hold down the <Del> key during the boot process and enter BIOS setup to 2.USB device wake-up (3-pinUSBPW1, USBPW2, USBPW3, USBPW4) 1.10.1 Rear panel connectors 1.10.2 Internal connectors 3.ATX power connectors (20-pinATXPWR1, 4-pinATX12V1) 4.Internal audio connectors (4-pinCD1, AUX1) 5.CPU, power and chassis fan connectors (3-pinCPU_FAN, CHA_FAN) 6.USB header (10-1pin USB56, USB78) 7.Front panel audio connector (10-1pin FP_AUDIO1) 8. Chassis intrusion connector (4-1pin CHASSIS1) 9.GAME/MIDI connector (16-1pin GAME1) 10.Serial ATA connectors (7-pinSATA1, SATA2) 11.System panel connector (10-1pin PANEL1) This connector accommodates several system front panel functions •System Power LED Lead (Green 3-pinPLED) •System Warning Speaker Lead (Orange 4-pinSPEAKER) •Reset Switch Lead (Blue 2-pinRESET) Page Page 2.1.1Creating a bootable floppy disk 2.1.2 Using AFUDOS to update the BIOS 2.1.3 Using AFUDOS to copy BIOS from PC 2.1.4 Using ASUS EZ Flash to update the BIOS 2.1.5 Recovering the BIOS with CrashFree BIOS 2. When the BIOS update process is complete, reboot the system To recover the BIOS from the support CD: Place the support CD in the 2. When the BIOS update process is complete, reboot the system Page BIOS menu screen 2.2.2 Menu bar 2.2.3 Navigation keys 2.2.4 Menu items 2.2.5 Sub-menuitems 2.2.6 Configuration fields 2.2.7 Pop-upwindow 2.2.8 Scroll bar 2.3.1 System Time [xx:xx:xxxx] 2.3.2 System Date [Day xx/xx/xxxx] 2.3.3 Legacy Diskette A [1.44M, 3.5 in.] Type [Auto] LBA/Large Mode [Auto] Block (Multi-sectorTransfer) [Auto] PIO Mode [Auto] DMA Mode [Auto] 2.3.5 IDE Configuration Enhanced Mode Support On [S-ATA] IDE Port Settings [Primary P-ATA+S-ATA] 2.3.6 System Information 2.4.1 JumperFree Configuration CPU VCore Voltage [Auto] AI Overclocking Tuner CPU Frequency (MHz) [XXX] (value is auto-detected) (value is auto-detected) 2.4.2 CPU Configuration 2.4.3 Chipset DRAM CAS# Latency [2.5 Clocks] DRAM RAS# Precharge [4 Clocks] DRAM RAS# to CAS# Delay [4 Clocks] DRAM Precharge Delay [8 Clocks] DRAM Burst Length [8 Clocks] 2.4.4 Onboard Devices Configuration OnBoard LAN Boot ROM [Disabled] 2.4.5 PCI PnP 2.4.6 USB Configuration USB Mass Storage Reset Delay [20 Sec] 2.5.1 Suspend Mode [S1 (POS) & S3 (STR)] 2.5.2 Repost Video on S3 Resume [No] 2.5.3 ACPI 2.0 Support [No] 2.5.4 ACPI APIC Support [Enabled] 2.5.5 BIOS ->AML ACPI Table [Enabled] 2.5.6Advanced Power Management (APM) Configuration Restore on AC Power Loss [Power Off] Power On By RTC Alarm [Disabled] Power On By External Modem [Disabled] Power On By PCI Devices [Disabled] Power On By PS/2 Keyboard [Disabled] Hardware Monitor CPU Temperature [xxxC/xxxF] MB Temperature [xxxC/xxxF] CPU Fan Speed [xxxxRPM] or [N/A] Chassis Fan Speed [xxxxRPM] or [N/A] 2.6.1 Boot Device Priority 2.6.2 Boot Settings Configuration Quick Boot [Enabled] Full Screen Logo [Enabled] Add On ROM Display Mode [Force BIOS] Sets the display mode for option ROM Configuration options: [Force BIOS] [Keep Current] 2.6.3 Security User Access Level (Full Access] No Access prevents user access to the Setup utility Change User Password To set a User Password: 1.Select the Change User Password item and press Enter Boot Sector Virus Protection [Disabled] Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Page 3.2.1 Running the support CD 3.2.2 Drivers menu 3.2.3 Utilities menu 3.2.4 ASUS Contact Information