Asus TX97-LE 20.Wake on LAN Activity Connector (3-pinWAKE

INSTALLATION .III (Connectors)

III.INSTALLATION

20.Wake on LAN Activity Connector (3-pin WAKE_LAN)

The WAKE_LAN connector allows the system to power up when there is a wakeup package (signal) received from the network through the ASUS PCI- L101 LAN card. Requires the ASUS PCI-L101 and an ATX power supply with at least 720mAmp 5VSB.

+5V Standby

Ground

PME

Wake on LAN Activity

32	ASUS TX97-LE User’s Manual

Contents

Page USER'S NOTICE Product Name: ASUS TX97-LE Manual Revision: Release Date: ASUSTeK COMPUTER INC Marketing Info Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS Page FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this manual is organized Item Checklist Features of the ASUS TX97-LEMotherboard Introduction to ASUS Smart Series of motherboards II.FEATURES Voltage Monitoring and Alert CPU Slow Down Auto Fan Off even in sleep mode Parts of the ASUS TX97-LEMotherboard ASUS TX97-LEMotherboard Layout Jumpers Expansion Slots Connectors Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 3.Keyboard Power Up (KBPWR) (Reserved for future use) Setting KBPWR Disable Enable Page Compatible Cyrix CPU Identification 2.System Memory (SIMM & DIMM) SIMM Memory Installation DIMM Memory Installation 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor 5.External Connectors 3.Parallel Printer Connector (PRINTER, 26-1pin block) NOTE: Serial printers must be connected to the serial port 4.Serial Port Connectors (COM1/COM2, two 10-1pin blocks) 5.CPU Cooling Fan Connectors (FAN, 3 pins) These are not jumpers, do not place jumper caps over these pins 6.Chassis Open Alarm Lead (CHASSIS, 4-1pins) 7.Primary / Secondary IDE connectors (Two 40-1pin block) 8.IDE activity LED (IDE LED, 2 pins) 9.ATX Power Supply Connector (ATXPWR, 20-pinblock) 10.AT Power Supply Connector (POWER, 12-pinblock) 12.Second IrDA-CompliantInfrared Connector (IR, 5-pinblock) UART2 Use Infra- red Chipset Features Setup 13.Message LED Lead (MSG.LED, 2 pins) 14.SMI Suspend Switch Lead (SMI, 2 pins) 15.ATX Power Switch/Soft Power Switch Lead (PWR.SW, 2 pins) 16.Reset Switch Lead (RESET, 2 pins) 17.System Power LED (PWR.LED, 3 pins) 20.Wake on LAN Activity Connector (3-pinWAKE_LAN) Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Features Menu Managing & Updating your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup Time Hard Disk Drives For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option Auto detection of hard disks on bootup Auto NOTE: SETUP Defaults are noted in parenthesis next to each function heading Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) BIOS Features Setup Details of BIOS Features Setup (BIOS HDD Sequence SCSI/IDE First (IDE) IDE SCSI Boot Sequence (C,A) Chipset Features Setup Details of Chipset Features Setup (Chipset SDRAM CAS# Latency (3T) SDRAM Speculative Read (Disabled) Passive Release (Enabled) Delayed Transaction (Disabled) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Onboard Serial Port 2 (2F8H/IRQ3) Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) PM Timers HDD Power Down Doze Standby PNP and PCI Setup Details of PNP and PCI Setup Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving (This page was intentionally left blank) ASUS Smart Motherboard Support CD Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults Symbios SCSI BIOS and Drivers Setting Up the ASUS PCI-SC200& PCI-SC860 Setting the INT Assignment for the ASUS PCI-SC200 Terminator Requirements for SCSI Devices Terminator Settings for the ASUS PCI-SC860 Terminator Settings for the ASUS PCI-SC200 SCSI ID Numbers for SCSI Devices SCSI ID Priority ASUS PCI-L101Fast Ethernet Card Features Software Driver Support Question and Answer