AT&T 992 BATTERIES

Charging the Handset Battery Pack

This battery should remain charged up to 15 days with the Ringer turned

on and up to 30 days with the Ringer off. A fully charged battery provides

an average talk time of about 10 hours.

The battery pack needs charging when:

• A new battery is installed in the handset.

• The phone beeps four times when you press P.

• The battery status symbol on the screen is only partly displayed.

• The phone does not respond when you press P.

Place the handset in the base either in the face-down or face-up position so

the CHARGING light turns on. The battery pack is typically fully charged in

six hours.

You can keep the battery fully charged by returning the handset to the

base after each use.

If you repeatedly get a low battery indicator,even after six hours of

charging,the battery should be replaced.

CAUTION: To reduce the risk of fire or injury to persons or

damage to the telephone,read and follow these instructions

carefully:

• Use only Replacement Battery 3300 (SKU# 90556).

• Do not dispose of the battery in a fire. The cell might explode.

Check with local codes for special disposal instructions.

• Do not open or mutilate the battery. Released electrolyte is

corrosive and may cause damage to the eyes or skin. It may be

toxic if swallowed.

• Exercise care in handling batteries in order not to short the battery

with conducting materials such as rings,bracelets, and keys. The

battery or conductor may overheat and cause harm.

• Charge the battery provided with or identified for use with this

product only in accordance with the instructions and limitations

specified in this manual.

• Observe proper polarity orientation between the battery and

battery charger.

42

BATTERIES

9355_book_1ATT 7/12/99 2:25 PM Page 42

Contents

Main REVISED 7/12/99 INSTALLATION.................................3 FEATURE SETUP..............................6 TELEPHONE OPERATION At the Handset............................18 TELEPHONE OPERATION At the Base..................................22 TELEPHONE MEMORY....................24 ANSWERING SYSTEM OPERATION At the Base..................................27 CONTENTS ANSWERING SYSTEM OPERATION At Cordless Handset or Touch Tone Phone........................32 CALLER ID OPERATION..................37 OPERATINGRANGE .......................41 BATTERIES....................................42 IN C ASE OF DIFFICULTY ................44 Page Page INSTALLATION About Softkeys Telephone Feature Setup Dial Mode Ringer Off / Battery Save Handset Ringer Selection 7 Caller ID Feature Setup Programming Home and Local Area Codes Turning Off Caller ID with Call Waiting 8 Call List Options Answering System Feature Setup Announcement Options Ring Select and Toll Saver Audible Message Alert Remote Access Code 10 Priority Call Signal Changing the Priority Calling Code Reviewing Feature Settings 11 Recording Your Announcement 12 Deleting an Announcement Setting the Clock 13 Caller Specific Outgoing Announcements Recording a Caller Specific Outgoing Announcement 14 Reviewing a Caller Specific Outgoing Announcement Deleting a Caller Specific Outgoing Announcement 15 Talking Caller ID Recording a Talking Caller ID (LOCAL) Announcement 16 Reviewing a Talking Caller ID (LOCAL) Announcement Making a Call Previewing a Number Before Calling Answering a Call Ending a Call Redial Handset Volume Temporary Tone Page Changing Channels Headset Jack Answering a Call Connecting to a Call with the Speakerphone Speaker Volume Mute Hold Base Ringer Volume Page/Intercom Handset Locator i TELEPHONE MEMORY Storing Numbers in Memory Storing a Pause in a Memory Number TELEPHONE MEMORY Storing a Name with a Memory Number Replacing a Stored Number Storing a Number and Name from Call History in Telephone Memory Viewing Numbers in Memory Page Turning the System On/Off About Mailboxes Message Playback Volume Announcement Play/Silent Answering Calls Call Screening/Intercept Announcement Bypass Listening to Your Messages Saving Messages 30 Deleting Messages Delete all messages in a mailbox Delete selected messages Replay deleted message Recording a Memo Message Window Display 32 Call Screening Connect with the Answering System From the Cordless Handset From a Touch Tone Phone Voice Help Menu Remote Access Commands Playing Messages 33 Page 35 Setting the Clock Remote ON/OFF Reviewing ON/OFF Status Turning System Off Turning System On Recording a Message When System is Off Changing Settings Reviewing Settings Exit Remote Access Audible Signals Sound: Meaning: About Caller Identification Call Waiting Incoming Call History Memory Match Reviewing Call History Display Dial Deleting Call Records from Call History Deleting a Specific Call Record Deleting All Call Records 39 Caller ID Display Messages OPERATING RANGE BATTERIES Charging the Handset Battery Pack Replacing the Handset Battery Pack BATTERIES 44 If the phone does not work at all, check these items first: If you have no dial tone: If you hear a two-beep signal when you try to use the handset: To re-initialize the handset and base: If you hear noise or interference when using the phone: If the phone does not ring when you receive a call: If your telephone misdials or you dont hear the other person right away: If the callers name or phone number is not displayed: 45 Page Page Page Remote Command Press