AT&T 992 - page 6

3 Connect the telephone line cord.

Plug one end of the telephone line cord into the jack labeled TEL

LINE on the back of the base. Plug the other end of the line cord

into a modular jack. Make sure the plugs snap firmly into place.

(If you are wall mounting the phone,use the short line cord, and

press the excess cord into the groove on the bottom of the base.)

4 Connect the power cord.

Plug the power adapter into the jack labeled POWER on the back

of the base. Loop the cord through the strain-relief groove and

press the cord into the groove on the back of the base. Plug the

AC adapter on the power cord into an electrical outlet. The

Message Window flashes CL.

NOTE: Connect power to the base unit before placing the

handset in the cradle.

5 Mount the base on the wall. (WALL MOUNTING ONLY)

Hold the base so the mounting knobs on the standard wall jack

will fit into the holes on the bottom of the base. Slide the base

down onto the knobs until it locks into place.

6 Attach belt clip (optional).

If you wish,you can attach the belt clip to the cordless handset,

following the illustrations below. (The handset may not charge in

the face-up position when the belt clip is attached.)

7 Charge the handset battery.

Place the handset face up or face down in the base. The

CHARGING light on the base goes on to show the handset is in

the right position to charge the battery.

For best battery performance,charge the battery at least 12 hours

the first time. After the first charge,the battery will quick-charge

in only six hours.

INSTALLATION

4

To Attach To Remove

9355_book_1ATT 7/12/99 2:25 PM Page 4

Contents

Main REVISED 7/12/99 INSTALLATION.................................3 FEATURE SETUP..............................6 TELEPHONE OPERATION At the Handset............................18 TELEPHONE OPERATION At the Base..................................22 TELEPHONE MEMORY....................24 ANSWERING SYSTEM OPERATION At the Base..................................27 CONTENTS ANSWERING SYSTEM OPERATION At Cordless Handset or Touch Tone Phone........................32 CALLER ID OPERATION..................37 OPERATINGRANGE .......................41 BATTERIES....................................42 IN C ASE OF DIFFICULTY ................44 Page Page INSTALLATION About Softkeys Telephone Feature Setup Dial Mode Ringer Off / Battery Save Handset Ringer Selection 7 Caller ID Feature Setup Programming Home and Local Area Codes Turning Off Caller ID with Call Waiting 8 Call List Options Answering System Feature Setup Announcement Options Ring Select and Toll Saver Audible Message Alert Remote Access Code 10 Priority Call Signal Changing the Priority Calling Code Reviewing Feature Settings 11 Recording Your Announcement 12 Deleting an Announcement Setting the Clock 13 Caller Specific Outgoing Announcements Recording a Caller Specific Outgoing Announcement 14 Reviewing a Caller Specific Outgoing Announcement Deleting a Caller Specific Outgoing Announcement 15 Talking Caller ID Recording a Talking Caller ID (LOCAL) Announcement 16 Reviewing a Talking Caller ID (LOCAL) Announcement Making a Call Previewing a Number Before Calling Answering a Call Ending a Call Redial Handset Volume Temporary Tone Page Changing Channels Headset Jack Answering a Call Connecting to a Call with the Speakerphone Speaker Volume Mute Hold Base Ringer Volume Page/Intercom Handset Locator i TELEPHONE MEMORY Storing Numbers in Memory Storing a Pause in a Memory Number TELEPHONE MEMORY Storing a Name with a Memory Number Replacing a Stored Number Storing a Number and Name from Call History in Telephone Memory Viewing Numbers in Memory Page Turning the System On/Off About Mailboxes Message Playback Volume Announcement Play/Silent Answering Calls Call Screening/Intercept Announcement Bypass Listening to Your Messages Saving Messages 30 Deleting Messages Delete all messages in a mailbox Delete selected messages Replay deleted message Recording a Memo Message Window Display 32 Call Screening Connect with the Answering System From the Cordless Handset From a Touch Tone Phone Voice Help Menu Remote Access Commands Playing Messages 33 Page 35 Setting the Clock Remote ON/OFF Reviewing ON/OFF Status Turning System Off Turning System On Recording a Message When System is Off Changing Settings Reviewing Settings Exit Remote Access Audible Signals Sound: Meaning: About Caller Identification Call Waiting Incoming Call History Memory Match Reviewing Call History Display Dial Deleting Call Records from Call History Deleting a Specific Call Record Deleting All Call Records 39 Caller ID Display Messages OPERATING RANGE BATTERIES Charging the Handset Battery Pack Replacing the Handset Battery Pack BATTERIES 44 If the phone does not work at all, check these items first: If you have no dial tone: If you hear a two-beep signal when you try to use the handset: To re-initialize the handset and base: If you hear noise or interference when using the phone: If the phone does not ring when you receive a call: If your telephone misdials or you dont hear the other person right away: If the callers name or phone number is not displayed: 45 Page Page Page Remote Command Press