AT&T 992 - page 48

If the caller’s name or phone number is not displayed during

Call Waiting:

• Make sure you subscribe to combined Caller ID with Call Waiting

service.

• The screen may not display the call information if someone is on an

extension phone.

• The Caller ID with Call Waiting feature is inactive during a power

interruption.

• Make sure the battery is charged.

• Make sure Caller ID with Call Waiting is turned on (see the CALLER ID

OPERATION section of this manual).

If speakerphone conversation sounds distorted:

After the phone is powered up,the speakerphone initializes for about 10–15

seconds the first time it is used. Conversation should be clear after this.

If messages are incomplete:

• If a caller leaves a very long message,part of it may be lost when the

system disconnects the call after three minutes.

• If the caller pauses for more that seven seconds,the system stops

recording and disconnects the call.

• If the system’s memory becomes full during a message,the system

stops recording and disconnects the call.

If you have difficulty hearing messages:

Check the volume setting.

If the system does not answer after the correct number of rings:

• Make sure that the two-digit Message Window in the base is on. If it is

off,press O.

• If Toll Saver is on,the number of rings changes to two when you have

new messages waiting.

• In some cases,the system may be affected by the ringing system used

by the local telephone company.

• If the memory is full or the system is off,the system answers after

10 rings.

46

IN CASE OF DIFFICULTY

9355_book_1ATT 7/12/99 2:25 PM Page 46

Contents

Main REVISED 7/12/99 INSTALLATION.................................3 FEATURE SETUP..............................6 TELEPHONE OPERATION At the Handset............................18 TELEPHONE OPERATION At the Base..................................22 TELEPHONE MEMORY....................24 ANSWERING SYSTEM OPERATION At the Base..................................27 CONTENTS ANSWERING SYSTEM OPERATION At Cordless Handset or Touch Tone Phone........................32 CALLER ID OPERATION..................37 OPERATINGRANGE .......................41 BATTERIES....................................42 IN C ASE OF DIFFICULTY ................44 Page Page INSTALLATION About Softkeys Telephone Feature Setup Dial Mode Ringer Off / Battery Save Handset Ringer Selection 7 Caller ID Feature Setup Programming Home and Local Area Codes Turning Off Caller ID with Call Waiting 8 Call List Options Answering System Feature Setup Announcement Options Ring Select and Toll Saver Audible Message Alert Remote Access Code 10 Priority Call Signal Changing the Priority Calling Code Reviewing Feature Settings 11 Recording Your Announcement 12 Deleting an Announcement Setting the Clock 13 Caller Specific Outgoing Announcements Recording a Caller Specific Outgoing Announcement 14 Reviewing a Caller Specific Outgoing Announcement Deleting a Caller Specific Outgoing Announcement 15 Talking Caller ID Recording a Talking Caller ID (LOCAL) Announcement 16 Reviewing a Talking Caller ID (LOCAL) Announcement Making a Call Previewing a Number Before Calling Answering a Call Ending a Call Redial Handset Volume Temporary Tone Page Changing Channels Headset Jack Answering a Call Connecting to a Call with the Speakerphone Speaker Volume Mute Hold Base Ringer Volume Page/Intercom Handset Locator i TELEPHONE MEMORY Storing Numbers in Memory Storing a Pause in a Memory Number TELEPHONE MEMORY Storing a Name with a Memory Number Replacing a Stored Number Storing a Number and Name from Call History in Telephone Memory Viewing Numbers in Memory Page Turning the System On/Off About Mailboxes Message Playback Volume Announcement Play/Silent Answering Calls Call Screening/Intercept Announcement Bypass Listening to Your Messages Saving Messages 30 Deleting Messages Delete all messages in a mailbox Delete selected messages Replay deleted message Recording a Memo Message Window Display 32 Call Screening Connect with the Answering System From the Cordless Handset From a Touch Tone Phone Voice Help Menu Remote Access Commands Playing Messages 33 Page 35 Setting the Clock Remote ON/OFF Reviewing ON/OFF Status Turning System Off Turning System On Recording a Message When System is Off Changing Settings Reviewing Settings Exit Remote Access Audible Signals Sound: Meaning: About Caller Identification Call Waiting Incoming Call History Memory Match Reviewing Call History Display Dial Deleting Call Records from Call History Deleting a Specific Call Record Deleting All Call Records 39 Caller ID Display Messages OPERATING RANGE BATTERIES Charging the Handset Battery Pack Replacing the Handset Battery Pack BATTERIES 44 If the phone does not work at all, check these items first: If you have no dial tone: If you hear a two-beep signal when you try to use the handset: To re-initialize the handset and base: If you hear noise or interference when using the phone: If the phone does not ring when you receive a call: If your telephone misdials or you dont hear the other person right away: If the callers name or phone number is not displayed: 45 Page Page Page Remote Command Press