INTRODUCTION TO YOUR
AT&T REMOTE MONITOR STARTER KIT ///
Thank you for your purchase of the AT&T Remote Monitor Starter Kit. The XG1000 Controller (the terms “Controller” and “Gateway” should be viewed as synonomous), a small dedicated computer, allows you to access and control cameras and other devices in your home, and make this information available to you wherever you are. You can access the XG1000 from any
PC (must be running Windows XP or 2000) with an internet connection anywhere in the world.
You can even use the XG1000 from your cell phone. You only need to use a PC to set up your XG1000. From then on, no PC is required for the XG1000 to function.
The system uses IP cameras. These are devices that communicate through normal internet cabling. If you do not wish to run new Ethernet wiring in your home, you can use Power Line Communication modules (PLC’s) to use the existing power outlets in your home, instead. Two of these modules are included in the starter kit.
In addition to the cameras, you can also use sensor modules in your home to monitor temperature, detect a door or window opening, wet conditions and motion. These are battery powered devices that communicate wirelessly with the controller. You can even turn lights and appliances on and off, by purchasing optional power controllers.
WITH YOUR AT&T REMOTE MONITOR ACCOUNT YOU CAN:
■View Live Video
■Check Device Status
■Arm and Disarm Devices
■Set Up Rules to Perform Actions Based on Events or Time of Day
■ Record Snapshots and Video Clips
■ Review Archived Events
If you have a JAVA enabled wireless phone from AT&T, you can access most of the controller functions remotely through the phone. You need to download an application to your wireless phone from AT&T to do this. Other cell phones can receive text notifications, but cannot view live video or control devices.
FIRST TIME SETUP ///
PREPARATION:
YOUR STARTER KIT CONTAINS THE FOLLOWING ITEMS:
■XG1000 Controller [X1] with AC Power Supply [A1] and Ethernet Cable [E1]
■IP Camera [C1] with AC Power Supply [A2]
■2 HomePlug Turbo 85Mbps PLC Ethernet Adapters [H1 & H2] and 2 Ethernet Cables [E2 & E3]
■Door Window Contact Sensor [D1] with Batteries [B1]
■Controller Mounting Hardware - 2 Feet [F1] & 2 Wall Brackets [G1]
■Documentation
XG1000 | IP CAMERA | 2 HOMEPLUG TURBO 85MBPS | DOOR/WINDOW | MOUNTING | ||||||||||||||
CONTROLLER | [C1] |
| PLC ETHERNET ADAPTERS | CONTACT SENSOR | FEET/BRACKETS | |||||||||||||
[X1] |
|
|
|
|
| [H1 & H2] | [D1] | [F1 & G1] | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
XG1000 AC | IP CAMERA AC | 3 ETHERNET | CONTACT SENSOR |
POWER SUPPLY | POWER SUPPLY | CABLES | BATTERIES |
[A1] | [A2] | [E1, E2 & E3]] | [B1] |
Please check the contents of your starter kit prior to starting installation. In addition to the items supplied in the kit you will also need a DSL/Cable Modem or other high speed internet connection, a router - or home network device - with at least two unused ports, and a Windows XP or 2000 PC to set up the XG1000 Controller.
The PC you will be using to install the system needs to be on the same router or local network as the XG1000 Controller. After the installation, you can access the system from any PC connected
to the Internet.
Your Internet connection and router should be functional before proceeding with this installation. As part of the purchase, you will have set up a AT&T Remote Monitor Account; you will need the UserID and Password that you created for this account later in the setup procedure.
I | 2 |
