o w n e r s | m a n u a l |
CONNECTING AND OPERATING THE SUBWOOFER - METHOD 2
With other brands of front speakers
1.On the rear of the receiver there should be a single RCA type jack named
“Subwoofer Out” Connect a single RCA type audio cable from the “Subwoofer Out” jack to the “Sub Input” (jack #2 on diagram #2)
2.Plug the Subwoofer’s AC cord into an AC outlet. Do not use the accessory type AC outlets on the rear of the AV receiver.
3.Set the Low Pass Filter Control (knob #2 diagram #1) to match the model of speaker that you have in the front of your system. The best way to start finding the correct frequency is to set the control to the low level cut off of the front speakers. This specification can be found in the owners manual of your speakers, or from the manufacturer. This is just a starting point however as room acoustics, placement and other variables dictate that you will need to experiment with this control to get the sound of the subwoofer to blend with that of the front speakers.
4.Adjust the Volume Control (knob #1 diagram #1) to match the output of the system. This can be done to suit your personal taste, and room size. Start somewhere in the middle of the dial and adjust as you feel is necessary.
CONNECTING AND OPERATING THE SUBWOOFER - METHOD 3
For LFE or Home Theater Applications
•The
•When using this input, the Low Pass Filter Control (Knob #2 on Diagram #1) and the Volume Control (Knob #1 on Diagram#1) are bypassed. This means that the subwoofer will output its total possible frequency range, which is up to 120Hz. The volume output of the subwoofer must be adjusted from the Bass Management system built into your Audio Video Receiver.
Note: In music applications, use of the “Direct Input” can cause an overlap in the bass response between the subwoofer and the front speakers, and usually a “boomy” sound is the result. It is recommended to use connection Method 1 or 2 for systems where both music and home theater are being utilized.
1.On the rear of the receiver there should be a single RCA type jack named
“Subwoofer Out” Connect a single RCA type audio cable from the “Subwoofer Out” jack to the “Direct Input” (jack #1 on diagram #2)
2.Plug the Subwoofer’s AC cord into an AC outlet. Do not use the accessory type AC outlets on the rear of the AV receiver.
3.No adjustments to the Low Pass Filter Control (knob #2 diagram #1) or the Volume Control (knob #1 diagram #1) are necessary as these controls are bypassed.
4.Adjust the Volume Control (knob #1 diagram #1) to match the output of the system. This can be done to suit your personal taste, and room size. Start somewhere in the middle of the dial and adjust as you feel is necessary.
CONNECTING AND OPERATING THE SUBWOOFER - METHOD 4
High Level or Speaker Type Inputs
•These inputs are provided for use with receivers or amplifiers that do not have a built in RCA type subwoofer jack. If your receiver has an RCA subwoofer type jack it is recommended to use it, using methods 1, 2 or 3.
1.On the rear of your receiver, locate the Front Speaker outputs. Connect a pair of speaker cables from the receivers front speaker outputs to the Speaker Inputs (jack #3 diagram #2) on the
2.Using an additional pair of speaker cables, connect from the speaker outputs on the
3.Make sure that you carefully match the Positive to Positive and Negative to Negative, on all speaker connections. Also make sure the left and right channels are wired separately and correctly.
4.Plug the Subwoofer’s AC cord into an AC outlet. Do not use the accessory type AC outlets on the rear of the AV receiver.
5.Set the Low Pass Filter Control (knob #2 diagram #1) to match the model of speaker that you have in the front of your system. The best way to start finding the correct frequency is to set the control to the low level cut off of the front speakers. This specification can be found in the owners manual of your speakers, or from the manufacturer. This is just a starting point however as room acoustics, placement and other variables dictate that you will need to experiment with this control to get the sound of the subwoofer to blend with that of the front speakers.
6.Adjust the Volume Control (knob #1 diagram #1) to match the output of the system. This can be done to suit your personal taste, and room size. Start somewhere in the middle of the dial and adjust as you feel is necessary.
WARRANTY OUTSIDE OF THE
UNITED STATES AND CANADA
Outside of North America the warranty may be changed to comply with local regulations. Ask your local athena TECHNOLOGIES® retailer for details of the limited warranty applicable in your country.
WARRANTY FOR UNITED STATES AND CANADA
(SEE BACK COVER)
athena TECHNOLOGIES®, SCTTM, and Create Your SoundTM, are trademarks of Audio Products International Corp. “Dolby”, “Dolby
4
