Atmel AT91CAP7A-STK manual CAP Starter Kit Development Tools , CAP Customizable Microcontroller

AT91CAP7A-STK®Starter Kit

for CAP Customizable Microcontroller

CAP Starter Kit Development Tools 

The CAP Starter Kit is supplied with an essential set of development tools in order to get started immediately. These include:

nInstructions for downloading IAR™ KickStart version of IAR Embedded Workbench® for ARM

nInstructions for downloading Altera’s free Quartus® 2 Web Edition tools for FPGA programming

nThe CAP7 Starter Kit Standalone Board

nA CD for documentation and software, including everything a user needs

to evaluate the CAP7 products, including software development tools and FPGA development tools

nThe board power supply with adaptors for Europe, United Kingdom, China and the United States

nA set of communication cables, including cables for USB and serial ports

Headquarters

Atmel Corporation

2325 Orchard Parkway

San Jose, CA 95131

USA

Tel 1 (408) 441-0311 Fax 1 (408) 487-2600

International

Atmel Asia

Room 1219

Chinachem Golden Plaza

77 Mody Road Tsimshatsui

East Kowloon

Hong Kong

TEL (852) 2721-9778 FAX (852) 2722-1369

Atmel Europe

Le Krebs

8, Rue Jean-Pierre Timbaud BP 309

JTAG

USB

Port

ADC

Ports

Serial

Data

Flash

Reset

OSC

XTALs

RS232

Port

	CAP7
RS232
Port
(DBGU)

ADC

Sensors

SPI

Header: 40pins

SDRAM

EBI

NAND

Flash

Header: 40pins

	FPGA
	Altera FPGA
PIOA	Cyclone II

MPIO EP2C8

Header: 40pins

2.8inch TFT Color LCD

JTAG

78054 St.-Quentin-en-Yvelines

Cedex, France

Tel: (33) 1-30-60-70-00

Fax: (33) 1-30-60-71-11

Atmel Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

Japan

TEL (81) 3-3523-3551

FAX (81) 3-3523-7581

Product Contacts

Technical Support

www.atmel.com/products/AT91CAP

Sales Contacts

www.atmel.com/contacts

Web Site

www.atmel.com

© 2008 Atmel Corporation. All rights reserved.

The CAP Customizable Microcontroller 

Atmel’s CAP is an ARM microcontroller-based system-on-chip with fast local memory, a wide range of industry standard peripherals and interfaces, and a Metal Programmable (MP) Block that allows the designer to add custom logic. By combining the performance, density and low power consumption of the fixed portion of the device with the flexibility of the MP Block, CAP enables application-specific products to be developed in a fraction of the time and at a fraction of the cost of standard-cell ASICs, but at a unit price close to that of standard cell devices. CAP also offers superior performance, smaller form factor and lower power consumption at a unit price significantly lower than an MCU-plus-FPGA combination for the same functionality.

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

Atmel®, logo and combinations thereof, and others, are registered trademarks, STK® and others are registered trademarks, CAPTM and others are trademarks of Atmel Corporation or its subsidiaries. ARM®, ARM7TDMI®, ARM Powered® logo and others are registered trademarks or trademarks of ARM Ltd. Other terms and product names may be trademarks of others.

REV.: 8521A-06/08/1K