AIE1
|
|
| IR Emitter |
Introduction |
|
|
|
3.5mm | White Stripe = + | Emitter & | |
|
| Docking Station | |
|
|
| 7/16" |
|
| 8 Feet | 9/16" |
|
| Emitter |
|
|
|
| Emitter Slides Into |
Adhesive |
|
| Docking Station |
Strip | Docking | 1/4" |
|
|
|
Station
The ATON AIE1 is a sophisticated, detachable IR emitter. It features a docking station that permits temporary removal of the emitter for rearranging or servicing components. The emitter housing can be removed for internal placement within components, if desired, for custom installations. The AIE1 produces
High-Output
Emitter
Housing
Internal
IR Emitter
Connecting Lead
Low-Output
Installation
•Locate the component’s IR receiver window. Thoroughly clean this window to remove fingerprints, dust, etc.
•Peel the protective layer off of the adhesive strip on the docking station and apply to the IR receiver window.
•Orient the docking station vertically, then press down for several seconds to ensure good contact with the adhesive.
•Slide the emitter down from the top into the docking station. It should snap into place.
•Connect the 3.5mm plug into an ATON DLA 2/4/6 Speaker Selector, AIB4 Amplified IR Connection Block or other source of IR.
•Remove the emitter from the docking station by sliding it upward.
Attach Docking Station to IR Receiver Window w/Adhesive Strip
Slide Emitter into
Docking Station
Emitter Properly Installed
Installation Notes:•Read the Owner’s Manual for the component to be controlled to find where the IR receiver window is located. A flashlight can also be useful for this purpose.
•Emitters can be attached without the docking station. Use an extra adhesive strip (included) applied directly to the flat side of the emitter.
•Use a new adhesive strip when
•The outer shell of the AIE1 is transparent to IR so that
Typical Installation
|
| Digital Music Server |
AIR1 | Remote Control |
|
Plasma Friendly |
|
|
|
| |
IR Receiver |
| AIE1 IR Emitter |
|
| Satellite |
|
| AIE1 IR Emitter |
PS2 |
| DVD |
|
| |
Power |
|
|
Supply | AIB4 | AIE1 IR Emitter |
To 120V AC | ||
(unswitched) | Amplified IR |
|
| Connection Block |
|
Caution:
Do not plug the AIE1 into an emitter jack that is set to HIGH Power or “Blaster” as this will damage the emitter.
Additional Locations for Emitter Placement
Since the AIE1 has high output from its curved surface, it may be attached to nearby surfaces such as shelves, doors, or cabinets. Use the LOW power setting (not blaster power) on the connection block.
Shelf
Cabinet
Door
Limited Warranty
ATON* warrants to the purchaser/end user (“you”) that the AIE1 is to be free from defects in materials and workmanship for a period of five (5) years from date of purchase (the “Warranty Period”). This warranty is trans- ferable to subsequent owners of the product as long as the original proof of purchase is retained. If you discover a defect in material or workmanship within the Warranty Period, you can obtain warranty service by contacting ATON during the Warranty Period at
This warranty shall not apply to equipment (a) not manufactured by ATON, (b) to equipment which was improperly installed, (c) which was repaired or altered by persons other than ATON or its authorized representatives or sub- ject to unauthorized tampering, alteration or modification, (d) damaged due to misuse, negligence, accident, acts of God (including, but not limited to, excess moisture, insects, lightning, flood, electrical surge, tornado, earth- quake, or other catastrophic events beyond ATON’s control), or (e) subject to improper operation, maintenance or storage or unreasonable use. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement. The foregoing remedies shall be your exclusive remedies for any breach of warranty.
Further, the foregoing warranty does not extend to equipment sold, but not manufactured by, ATON (“Third Party Products”). With respect to any Third Party Products, the warranty for such product shall be as provided by the manufacturer of such product, who will also be responsible for warranty service, and ATON will pass through to you any transferable warranty actually extended to ATON by the manufacturer.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
Notwithstanding the above, where applicable, if you qualify as a “consumer” under the
ATTENTION: TO OUR VALUED CONSUMERS
Valid proof of purchase is required for all warranty services. Warranty service requests made without proof of date of purchase will be denied. Please keep the original sales receipt for your records and send a copy to request warranty service.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. * ATON is a division of ELAN Home Systems, LLC.
www.atonhome.com or service@atonhome.com©2007 • All rights reserved. | P/N 227931 REV:B |
1 | 2 | 3 | 4 |