AMP102 / AMP110
OWNER’S MANUAL
Speakers
AB
2
AMP102
Stereo Power Amplifier
| Power |
Signal / Clip | Signal / Clip |
Left | Right |
5 1 5
Balance
Left Right
3
Volume
Min Max
4
FRONT PANEL CONTROLS
1. Power
The front panel power switch switches the AMP102/110 on or off. Red LEDs behind the faceplate indicate power status. Whenever the amplifier’s power switch is in the “ON” position the ring around the button is illuminated. When the amp is “Active” (receiving signal) the side lenses become illuminated and the signal LEDs show green. During “Standby” status (no signal) the side lenses are not illuminated and the signal LEDs show orange.
2. Speaker Selector
Selects speaker set ( A or B )
Figure 1. Front Panel
3. Balance
Fades speaker output between the Right and Left Channels
4. Volume
Adjusts amplifier volume. 5. Clip LEDs
Blinks red during signal clipping. Reduce volume slightly.
Shows solid green (AMP102) or orange (AMP110) during protect mode. Check speaker wires for shorts or extreme low impedance (< 4 ohms).
Connect
Receiver
Here
Line 1 | Line 2 | Line 2 |
IN | IN | OUT |
L
R
Serial Number:
6 7
CAUTION | AVIS |
RISK OF FIRE OR ELECTRIC SHOCK | AVIS: RISQUE DE CHOC ELECTRIQE |
NE PAS OUVRIR CE CARTER | |
DO NOT OPEN | RESERVE AU PERSONNEL AUTORISE |
CAUTION: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE | |
COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO | |
QUALIFIED PERSONNEL. |
|
WARNING: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE
COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
Mode | 12V Trigger | Auto On |
| + |
|
Stereo Bridged | IN - OUT | Trigger Normal |
8 9 10
Minimum Impedance: |
|
|
| Speaker A |
|
|
- | R | + | + | L | - | |
8 ohm Bridged |
|
|
|
|
|
|
4 ohm Stereo |
|
|
|
|
|
|
Light Bar Display |
|
|
|
|
|
|
On Off |
|
| + | Bridge - |
|
|
|
|
|
|
|
| |
| - | R | + | + | L | - |
|
|
| Speaker B |
|
|
11 12 13
MODEL AMP102 |
|
Custom Manufactured in China |
|
115V~ 60Hz 500W | 15 |
FUSE:T4AL 250V | |
230V~ 50Hz 500W | |
FUSE:T2AL 250V |
CAUTION: See User Manual Before
14 Replacing Fuse
Figure 2. Rear Panel
REAR PANEL CONTROLS
6. Line 1 Input
A switching input that can be used if a second source is desired and will take over when a signal is present and has at least a 5mV level. Whenever there is no signal at this input, or a signal with less than 5mV level, the amplifier switches back to the Line 2 or “primary” input.
7. Line 2 Input/Output
The primary line level input and output for a single source connection. 8. Mode Select Switch
Switches the amplifier from Stereo mode to Bridged mode. 9. 12V Trigger
Allows the AMP102/110 to be powered on by other electronics or to power on other electronics via a 3.5mm mini phone plug cable.
10. Power Mode
Sets the power on option of the AMP102/110. Set it to Normal for manual power on/off. Set to
11. Light Bar Display Control
Turns light bar display on front panel on or off. Does not control Signal/Clip LEDs or power button light ring.
12. Right Channel Speaker Output
Right channel terminals for speaker outputs A and B.
13. Left Channel Speaker Output
Left channel terminals for speaker outputs A and B. 14. Mains Power Inlet & Fuse Holder
Accepts IEC type line cord. A fuse in the integrated holder provides safety protection from fault conditions: replace fuse with one of same type and rating only.
15. Mains Voltage Selector
Voltage selection switch is preset to 115V (USA). For use in areas which require 230V contact your dealer. Fuse must be of type and rating marked on amplifier for use at local mains voltage.
4 | 13970 SW 72nd Ave. Portland, OR 97223 • 503.914.4688 • www.audiosource.net |
|