Installation, Product Package | Proxim CPN 63708 specs

▪

▪

▪

Tsunami MP.11 Installation and Management

The unit must not be covered and the air must be able to flow freely around the unit.

The unit must be kept away from vibration, excessive heat, and humidity, and kept free from dust.

The installation must conform to local regulations at all times.

INSTALLATION

The MP.11 supports two power methodsan AC power outlet and Active Ethernet. The power supply accepts an input AC voltage in the range of 100-240 VAC.

The installation procedure on page 9 provides instructions for attaching both the power and Ethernet connectors.

WARNING! For your own safety, use only the power cord supplied with the unit. The metal case of the MP-11 must be grounded through the ground connection that is provided on the metal case. The antenna grounding, the surge arrestor, and the MP.11 housing must be bonded together and grounded in one location to avoid ground current loops.

In situations without an external antenna (for example, during a desk tryout), the antenna cable is not required.

The Product Package

Each MP.11 comes with the following:

▪

▪

One metal base for ceiling or desktop mounting (includes two screws)

Mounting hardware

ºFour 3.5 mm x 40 mm screws

ºFour 6 mm x 35 mm plugs

▪

▪

One power supply

One Tsunami MP.11 Installation CD-ROM containing:

ºSoftware Installation Package (starts automatically when CD is inserted in CD-ROM drive; can be started by double-clicking SETUP.EXE.

ºOnline Help

ºDocumentation (Quick Install Guide, Installation and Configuration Guide)

ºScanTool (a utility with which you can obtain or set the IP address of the MP.11 for access; see “ScanTool” on page 17 for more information).

Chapter 2. Installation	8
CPN 63708	Issue Date: 02/05/2003

Image 8

Proxim CPN 63708 manual Installation, Product Package

Contents

Tsunami MP.11 Copyright Trademarks Contents Overview Wireless Network Topologies Point-to-Point Link Point-to-Multipoint Network Finding a Suitable Location InstallationIdentifying Network Topology and Equipment Installation Product Package Installing the MP.11 Tsunami MP.11 Installation and Management Attaching a Kensington Security Lock Optional Switching on the MP.11 Power Ethernet Link Wireless LinkBlinking Green when data sent Blinking Green when Installing Documentation and Software Online helpDocumentation ScanTool Tftp server Wall Mounting Mounting the MP.11Desktop Mounting Tsunami MP.11 Installation and Management Ceiling Mounting ScanTool Management OverviewMP.11 IP Address Static or Dynamic IP Address Static IP Address Dynamic IP Address with Dhcp WEB Interface Overview Command Line Interface Overview Ethernet Port Serial Port HyperTerminal Connection Properties Basic Management Rebooting and Resetting RebootingResetting Hardware Click Commands Î Reboot General Settings Soft Reset to Factory DefaultClick Commands Î Reset System Status System Configuration IP Configuration DescriptorUp Time IP Address Assignment Type Wireless Slot Default Router IP AddressDefault TTL Interfaces Interface Type Base Station System NameNetwork Name Frequency Channel Ethernet Port Monitoring Settings Wireless Show wif show worp show worpcfg Security Settings Encryption Passwords Using Telnet to Change PasswordsUsing the Web Interface to Change Passwords Using Snmp to Change Passwords Upgrading the MP.11 Web Interface StatusStatus tab shows the System Status and the System Traps System Status Configure Click Configure Î SystemSystem Systems Traps Dhcp Relay Agent IP ConfigurationNetwork IP Routing Wireless Slot a Ethernet Snmp IP Access Table TelnetTrap Groups Trap Host Table Serial Time out Security MAC AuthenticationRadius Authentication Filtering Encryption Ethernet Protocol Filter Ethernet Protocol Filtering Wired MAC Address Wired MaskWireless MAC Address Static MAC Pair Filtering Comment Wireless MaskSpanning Tree Wireless Threshold Storm ThresholdPer Address Threshold Ethernet Threshold General MonitorBroadcast Protocol Filtering Worp Icmp Radius Link Test FeaturesPer Station IP ARP Table Learn Table IP Routes Commands DownloadServer IP address File Name Reboot Upload Reset Help Command Line Interface Using Command HelpBoot Loader Command Line Interface Introduction Show Command Set CommandViewing and Changing Parameters Entering Strings Viewing Table Contents Working with TablesCreating a Table Row Modifying a Table Entry Modifying Several Table Entries Enabling, Disabling, or Deleting a Table Row Procedure Description ProceduresTftp Server Setup CLI Image File Download Click Commands Æ DownloadImage File Download Configuration Backup CLI Configuration File UploadClick Commands Æ Upload File Type Config File Operation Upload File Type Config File Operation Download Configuration RestoreCLI Configuration File Download CLI Soft Reset to Factory Defaults Soft Reset to Factory DefaultHard Reset to Factory Default Image File Download with the Bootloader Forced Reload Command Line Interface Command prompt is displayed enter the following commands For example Specifications Hardware Specifications Channel ID FCC/World Etsi GHz France Japan GHz Radio SpecificationsChannel Frequencies Troubleshooting LED Indicators Serial Link Does Not Work MP.11 Connectivity IssuesMP.11 Does Not Boot HyperTerminal Connection Properties Setup and Configuration Ethernet Link does not work Setup and Configuration Lost the MP.11 PasswordMP.11 Responds Slowly Web Interface Does Not Work Online Help Is Not Available Command Line Interface Does Not WorkTftp Server Does Not Work Changes Do Not Take Effect Glossary ARP Http Icmp WEP