Proxim CPN 63708 IMAGE FILE DOWNLOAD

Tsunami MP.11 Installation and Management

IMAGE FILE DOWNLOAD

In some cases, it may be necessary to upgrade the embedded software of the MP.11 by downloading

an image file. To download an image file through the Web Interface:

1. Set up the TFTP server as described in “TFTP Server Setup” on page 64.

2. Access the MP.11 as described in “Web Interface Overview” on page 20.

3. Click: Commands Æ Download.

4. Fill in the following details:

Server IP Address <IP address TFTP server>

File Name <image file name>

File Type Image

File Operation Download

5. Click OK to start the file transfer.

The MP.11 downloads the image file. The TFTP server program should show download activity after a

few seconds. When the download is complete, the MP.11 is ready to start the embedded software.

CLI Image File Download

To download an image file:

1. Set up the TFTP server as described in “TFTP Server Setup” on page 64.

2. Access the MP.11 as described in “Command Line Interface Overview” on page 21.

3. Enter the following command:

download <IP address TFTP server> <image file name> image

The MP.11 downloads the image file. The TFTP server program should show download activity after

a few seconds. When the download is complete and the system rebooted, the MP.11 is ready to

start the embedded software.

Chapter 7. Procedures 65

CPN 63708 Issue Date: 02/05/2003

Contents

Main Notices Contents Chapter 1. Overview WIRELESS NETWORK TOPOLOGIES Page Chapter 2. Installation IDENTIFYING NETWORK TOPOLOGY AND EQUIPMENT FINDING A SUITABLE LOCATION INSTALLATION Installing the MP.11 Page Attaching a Kensington Security Lock (Optional) SWITCHING ON THE MP.11 Connecting the Active Ethernet splitter to the Ethernet cabling INSTALLING DOCUMENTATION AND SOFTWARE MOUNTING THE MP.11 Desktop Mount Wall Mount Ceiling Mount Desktop Mounting Wall Mounting Page Ceiling Mounting Chapter 3. Management Overview MP.11 IP ADDRESS ScanTool Static or Dynamic IP Address Static IP Address Dynamic IP Address with DHCP WEB INTERFACE OVERVIEW COMMAND LINE INTERFACE OVERVIEW Ethernet port connected through the network or with a cross-over Ethernet cable between the Serial port of the MP.11 Ethernet Port Serial Port An ASCII terminal program, such as HyperTerminal. HyperTerminal Connection Properties Chapter 4. Basic Management REBOOTING AND RESETTING Applying Changes Rebooting Resetting Hardware Soft Reset to Factory Default GENERAL SETTINGS System Status SYSTEM CONFIGURATION IP CONFIGURATION Interfaces Wireless Slot WORP Base WORP Satellite WORP Base and WORP Satellite Mode Ethernet Port MONITORING SETTINGS Wireless Interfaces SECURITY SETTINGS Encryption Passwords Using Telnet to Change Passwords Using the Web Interface to Change Passwords Using SNMP to Change Passwords UPGRADING THE MP.11 Chapter 5. Web Interface Configure Monitor Commands STATUS CONFIGURE 1) System 2) Network IP Routing 3) Interfaces 4) SNMP Trap Groups IP Access Table Trap Host Table 5) Telnet Page 8) Security Encryption 9) Filtering Ethernet Protocol Filter Static MAC Pair Filtering Spanning Tree Storm Threshold Specifying a maximum number of frames per second as received from a single network device Specifying an absolute maximum number of messages per port Broadcast Protocol Filtering MONITOR 1) Wireless General Page Page Page Page 9) Learn Table 10) IP Routes COMMANDS 1) Download Page 4) Reset 5) Help Chapter 6. Command Line Interface INTRODUCTION Viewing and Changing Parameters on page 61 Boot Loader Command Line Interface USING COMMAND HELP VIEWING AND CHANGING PARAMETERS Show Command Set Command ENTERING STRINGS WORKING WITH TABLES Viewing Table Contents Creating a Table Row Modifying a Table Entry Modifying Several Table Entries Enabling, Disabling, or Deleting a Table Row Chapter 7. Procedures TFTP SERVER SETUP IMAGE FILE DOWNLOAD CLI Image File Download CONFIGURATION BACKUP CLI Configuration File Upload CONFIGURATION RESTORE CLI Configuration File Download SOFT RESET TO FACTORY DEFAULT CLI Soft Reset to Factory Defaults HARD RESET TO FACTORY DEFAULT FORCED RELOAD 3. Follow the procedure Image File Download with the Boot Loader to download an image file. IMAGE FILE DOWNLOAD WITH THE BOOTLOADER ScanTool Command Line Interface An ASCII terminal program such as HyperTerminal. Page Chapter 8. Specifications HARDWARE SPECIFICATIONS RADIO SPECIFICATIONS Channel Frequencies Chapter 9. Troubleshooting Setup and Configuration on page 78 LED INDICATORS MP.11 CONNECTIVITY ISSUES MP.11 Does Not Boot Serial Link Does Not Work HyperTerminal Connection Properties Setup and Configuration Ethernet Link does not work Blinking Green or Amber is traffic SETUP AND CONFIGURATION Lost the MP.11 Password The MP.11 Responds Slowly No DHCP server is available. The IP address of the MP.11 is already in use. There is too much network traffic. Web Interface Does Not Work Page Changes Do Not Take Effect Glossary