Fig. 1 Installation
I. Use universal template provided and locate on roof the desired mounting area. Observecautions for possible interference in headliner or steel roof.
2.Drill two 5/16" dia. holes through the fiberglass roof cap, the steel roof and headliner making certain the drill is 900to the roof.
3.Enlarge the 5/16" holes in the fiberglass roof to 1 3/8" dia.
Warning -Only enlarge the two holes in the roof cap. Do not enlarge the holes in the steel roof or headliner.
4.Remove the inside headliner.
5.Assemble the two selectedmounting bolts, cup washers,grommets, flat washersandjamb nuts to the steel roof using the wrench provided. Make certain you apply sealant (not included) as shown.
6.Replace headliner.
7.Assemble radio mounting plate assemblyto bolt studs as shown.
8.Complete wiring.
9.Place housing below radio plate assembly and connect speakerwiring to radio wiring.
10.Securehousing using six screwsand washers provided.
11.Insert the two 1 3/8" plugs in fiberglass headliner using sealant to insure water-proof seal.. 12.SeeFig. 4 if installing CElOO/CE200/CE300.
Fig. 2 Installation
I. Use universal template provided and locate on roof the desired mounting area. Observecautions for possible interference in headliner or steel roof.
2.Drill rn'o 5/16" dia. holes through the fiberglass roof cap, the steel roof and headliner making certain the drill is 900to the roof. J. Remove the inside headliner.
4.Assemble the two selectedmounting bolts, cup washers,grommets, flat washersandjamb nuts to the steel roof using the wrench provided. Make certain you apply sealant (not included} as shown.
5.Replace headliner.
6.Assemble radio mounting plate assembly to bolt studs as shown.
7.Complete wiring.
8.Place housing below radio plate assembly and connect speakerwiring to radio wiring.
9.Securehousing using six screwsand washers provided.
IO.SeeFig. 4 if installing CEI00/CE200/CEJOO.
Fig. 3 Installation
I. Use universal template provided and locate on roof the desired mounting area. Observecautions for possible interference in headliner or steel roof.
2.Drill two 5/16" dia. holes through the fiberglass roof cap, the steel roof and headliner making certain the drill is 90° to the roof.
3.Assemble the two selectedmounting bolts, cup wash~rs,grommets, flat wa$hersandjamb nuts to the steel roof using the wrench provided. Make certain you apply sealant (not included) as shown.
4.Assemble radio mounting plate assembly to bolt studs as shown.
5.Complete wiring.
6.Place housing below radio plate assembly and connect speakerwiring to radio wiring.
7.Securehousing using six screws and washers provided.
8.SeeFig. 4 if installing CElOO/CE200/CE300.
Fig. 4 Installation
1.For figure I installation: Follow steps 1-11 then refer to Fig. 4 and follow instructions below it.
2.For figure 2 installation: Follow steps 1-9 then refer to Fig. 4 and follow instructions below it.
3.For figure 3 installation: Follow steps 1-7 then refer to Fig. 4 and follow instructions below it.
Figure 4 Installation: Only for CElOO/CE200/CE300
I.The entire housing and mounting plate (less radio) should now be securedto the roof as shown in Fig. 4
2. Insert mounting sleeve into housing opening and bend all tabs outward to secureit.
3. Reach through opening to accessradio wimg connector and plug into radio. 4. Reach through opening to accessantenna lead and plug into radio.
5. Pre-test radio.
6. Slide radio into housing until locked in place.
