Azden 15HT, 105UPR, 105ULH BODY-PACK Transmitter 15BT/EX-503L, XLR PLUG-IN Transmitter 15XT

(8) Phone Output Adjustment

Using the supplied tool, turn the screw clockwise to increase and counterclock- wise to decrease the audio level presented at the earphone monitor jack.

(9) Shoe-mount

Attach the 105UPR to the shoe-mount on the video camera by sliding it into place. Turn the thumb-wheel clockwise to tighten and counterclockwise to remove.

(10) Antenna

For best reception the antenna should be pointed in an upward fashion. Use caution and do not force it in this position.

BODY-PACK TRANSMITTER (15BT/EX-503L)

(11)Remove the battery compartment lid by sliding it down.

(12)Insert two fresh Alkaline “AA” batteries into the compartment. Make sure the battery polarity is correct as marked inside the battery compartment.

Inside the battery compartment you will also find #13 and #16

(13) MIC LEVEL Control

The MIC LEVEL control enables you to adjust the audio level of the micro phone. Using the supplied tool, turn the dial clockwise to increase, or counterclockwise to decrease the microphone’s audio output level.

(16) Frequency Selection

Frequency adjustment is accomplished by setting the two controls inside the battery compartment. With the frequency GROUP dial on the left (col- umn A on the included chart) you can select any of the 10 frequency groups (numbered 0-9). With the frequency CHANNEL dial on the right (column B on the included chart) you can select any of 10 frequency channels (numbered 0-9). There are actually 92 possible selections.

(14) POWER

This switches the transmitter “ON or “OFF”

(15) MIC Input Jack

Plug the supplied EX-503L microphone into the MIC jack and tightened the collar until it is snug (DO NOT OVERTIGHTEN). In addition to the EX-503L, other lapel and/or headset microphones with 3.5mm plugs can also be used with the 15BT.

(17) Audio Standby

The Audio Standby switch serves as a mute switch. In the STBY position the audio output from the 15BT is muted. In the ON position audio is transmitted.

(18) Belt-clip

Use this to attach the 15BT to a belt on the subject.

XLR PLUG-IN TRANSMITTER (15XT)

(19)Open the battery compartment lid and insert two fresh Alkaline “AA” batteries. Make sure the battery polarity is correct as marked inside the battery compartment.

(20)POWER

Switches the transmitter “ON” or “OFF”

(21) AUDIO

Prior to first turning the 15XT “ON” it is best to set the AUDIO switch to “OFF”.

When you are ready to begin transmitting, switch to “ON”. The “OFF” position acts as a “mute” that maintains the RF signal but turns off the audio.

(22) MIC Connector/Locking Ring

This 3-pin XLR connector is the microphone input. Any metal body low impedance microphone with a corresponding connector can be attached here. Once the microphone is plugged into the 15XT the locking ring

should be rotated clockwise until snug. To remove the microphone, first rotate

the locking ring counterclockwise and then, while pressing the XLR release, pull the microphone away from the 15XT.

(23) MIC LEVEL Control

The MIC LEVEL control enables you to adjust the audio level of the micro- phone. Using the supplied tool, turn the dial clockwise to increase, or counterclockwise to decrease the microphone’s audio output level.

(24) Frequency Selection

Frequency adjustment is accomplished by setting the two controls inside the battery compartment. With the frequency GROUP dial on the left (col- umn A on the included chart) you can select any of the 10 frequency groups (numbered 0-9). With the frequency CHANNEL dial on the right (column B on the included chart) you can select any of 10 frequency channels (numbered 0-9). There are actually 92 possible selections.