B&B Electronics EIR203-SC quick start Guide, Quick Start, Front Panel, DIN Rail Mounting

Models: EIR203-3SC EIR203-2ST EIR203-3ST EIR203-ST EIR203-2SC EIR203-MT EIR203-MC EIR203-3MT EIR203-2MC EIR203 EIR203-SC

1 2
Download 2 pages 26.59 Kb
Page 1
Image 1
GUIDE

GUIDE

EIR203 Series Quick Start

Guide

Package Contents

EIR203 Series Industrial, Unmanaged, Ethernet Switch

Quick Start Guide (One per shipment)

Power Terminal Block (installed)

Fiber Optic Dust Covers (installed on fiber optic models)

If any item is missing or damaged, contact B&B Electronics for a replacement

EIR203 1308qsg-1/2

© 2008 by B&B Electronics. All rights reserved.

1.Slide and hold the DIN clip toward the bottom of the switch. Angle the top portion of the DIN mount over the top of DIN Rail.

2.Move the switch so that it is parallel with the DIN Rail.

3.Let go of the DIN Clip. The spring should return it to its original position.

Attach Power Leads

External Supply Required

QUICK START

Front Panel

 

 

 

EIR203 (3 Fiber)

 

 

EIR203 (1 Fiber, 2 RJ-45)

 

 

 

 

 

 

 

 

 

 

1

Power Terminal Block

 

2 Position, Removable

 

 

2

PWR LED

 

ON When Power Applied

 

 

 

3

Fiber Optic SPD LED

 

Normally OFF (100BaseFx)

 

 

 

3

Fiber Optic LINK LED

 

ON When Fiber Port Linked

 

 

 

4

Fiber Ports

 

Number and type depends on Model

 

 

 

5

RJ45 Ports

 

Number depends on model

 

 

 

6

RJ45 LINK LED

 

On when RJ45 Port Linked

 

 

 

 

 

 

Flashes When Data Transmitted

 

 

 

6

RJ45 SPD LED

 

On if 100 mbps

 

 

 

 

 

 

 

 

 

 

Warning: Work Safe – Equipment damage or electrical shock hazard exists. DO NOT ATTACH OR REMOVE LEADS WITH THE POWER SUPPLY ENERGIZED!

1.Loosen the screw to open the terminal block lead clamp.

2.Insert the power lead. TB will accept 12-28 AWG wire.

3.Tighten the screw to close the terminal block lead clamp. Ensure the clamp holds the lead securely. However, do not over tighten.

NOTE: For replacement Terminal Block order Part # 7444.

Attach RJ45 Cable

(If equipped)

B&B ELECTRONICS

DIN Rail Mounting

Female RJ45

1.Auto MDI/MDI-x is supported. A straight through or cross-over cable may be used.

2.10/100BaseT auto negotiation and full/half- duplex are supported.

MDI Cable Pinout

Pin Signal

1Tx+

2Tx-

3Rx+

6Rx-

MDI-X Cable Pinout

Pin Signal

1Rx+

2Rx-

3Tx+

6Tx-

International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104 www.bb-elec.comorders@bb-elec.comsupport@bb-elec.com

European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445 www.bb-europe.comorders@bb-europe.comsupport@bb-europe.com

Page 1
Image 1
B&B Electronics EIR203-SC, EIR203-3ST quick start EIR203 Series Quick Start Guide Package Contents, Front Panel