Manuals / Baldor / Marine Equipment / Marine Battery

Baldor MN781W manual Simplified Operating Instructions

Models: MN781W

1 16
Download 16 pages 56.25 Kb
Page 3
Image 3

i.SIMPLIFIED OPERATING INSTRUCTIONS

IMPORTANT – You must read these simplified operating instructions before proceeding. These instructions are to be used as a reference only and are not intended to replace the detailed instructions provided herein. You must read the Safety Warning below before proceeding.

! WARNING! Disconnect main power when making connections to the control.

A.AC Line Connection – Connect the AC line to L1 and L2 terminals of Terminal Block TB1 and the ground wire (Earth) to the green ground screw as shown in Figure 4, on page 6, and as described in Section IIA, on page 6, and Section IIB, on page 6. Set Jumpers J1 and J2 to the corresponding AC line input voltage (115 or 208/230 Volts AC).

B.Motor Connection – Connect the motor to U, V and W terminals of Terminal Block TB1 as shown in Figure 4, on page 6, and as described in Section IIC, on page 6.

C.Start/Stop Switch – The control is supplied with a prewired Start/Stop Switch as described in Section IIE, on page 6, which is used to start and stop the control. In Manual Start Mode, this switch must be used to start the control each time the AC power is lost or the control shuts down due to a fault.

D.Jumper Settings – All jumpers are factory set for most applications. Be sure Jumper J3 is set to the correct motor HP. See Section IIIB, on page 7.

E.AC Line Fusing – Install a fuse or circuit breaker in the AC line. Fuse each conductor that is not at ground potential. See Section VII, on page 10, for recommended fuse size.

F.Trimpot Settings – All trimpots have been factory set as shown in Figure 2, on page 3. Trimpots may be readjusted as described in Section VIII, on page 10.

G.Diagnostic LEDs – After power has been applied, observe the LEDs to verify proper con- trol operation as described in Section IX, on page 13.

ii.

! SAFETY WARNING! Please read carefully

This product should be installed and serviced by a qualified technician, electrician, or elec- trical maintenance person familiar with its operation and the hazards involved. Proper installa- tion, which includes wiring, mounting in proper enclosure, fusing or other overcurrent protection, and grounding can reduce the chance of electrical shocks, fires, or explosion in this product or products used with this product, such as electric motors, switches, coils, solenoids, and/or relays. Eye protection must be worn and insulated adjustment tools must be used when work- ing with control under power. This product is constructed of materials (plastics, metals, carbon, silicon, etc.) which may be a potential hazard. Proper shielding, grounding, and filtering of this product can reduce the emission of radio frequency interference (RFI) which may adversely affect sensitive electronic equipment. If further information is required on this product, contact the factory. It is the responsibility of the equipment manufacturer and individual installer to sup- ply this Safety Warning to the ultimate end user of this product. (SW effective 11/1992.)

This control contains electronic Start/Stop circuits that can be used to start and stop the con- trol. However these circuits are never to be used as safety disconnects since they are not fail- safe. Use only the AC line for this purpose.

Be sure to follow all instructions carefully. Fire and/or electrocution can result due to improp- er use of this product.

This product complies with all CE directives pertinent at the time of manufacture. Contact factory for detailed installation and Declaration of Conformity. Installation of a CE approved RFI filter is required. Additional shielded motor cable and/or AC line cables may

be required along with a signal isolator (ID5SI-2).

1

Page 2 Page 4
Page 3
Image 3
Baldor MN781W manual Simplified Operating Instructions
Page 2 Page 4

MN781W specifications

The Baldor MN781W is a versatile and robust motor designed for various industrial applications. Known for its high performance and efficiency, this motor is an integral component in diverse sectors, including manufacturing, agriculture, and energy production. Its design emphasizes durability, reliability, and energy efficiency, making it a preferred choice for many professionals.

One of the main features of the Baldor MN781W is its premium efficiency rating, which ensures reduced energy consumption and lower operational costs. This motor meets or exceeds the efficiency standards set by the National Electrical Manufacturers Association (NEMA), contributing to substantial energy savings over its lifespan. When compared to traditional motors, the MN781W not only helps in cutting energy expenses but also supports environmentally friendly initiatives by minimizing carbon footprints.

The MN781W motor utilizes advanced insulation materials and coating technologies, providing enhanced protection against moisture, dust, and other environmental factors. This ensures optimal performance in challenging conditions while prolonging the motor’s life. The unique design of the motor housing and internal components minimizes heat generation, which is essential for extending operational longevity and preventing breakdowns.

In terms of technological features, the MN781W incorporates state-of-the-art bearing designs that reduce friction and enhance overall efficiency. This enables the motor to operate smoothly under heavy loads, which is particularly beneficial in industrial applications requiring consistent performance. Additionally, the motor is equipped with built-in thermal protection, which automatically shuts down the motor in case of overheating, thereby preventing damage and ensuring safety.

Another significant characteristic of the Baldor MN781W is its ease of installation and maintenance. The motor is designed with user-friendly access points for wiring and inspection, allowing technicians to conduct routine checks and repairs with minimal downtime. Furthermore, its modular design supports a range of mounting options, enabling seamless integration into existing systems.

In conclusion, the Baldor MN781W stands out as a reliable, energy-efficient motor that meets the demands of modern industries. With its premium efficiency rating, advanced protection features, and easy maintenance, it is an excellent choice for any business looking to enhance operational efficiency and reduce costs. Whether used in heavy machinery or process equipment, the MN781W ensures optimal performance and reliability, making it a valuable investment in industrial applications.