Manuals / Baracoda / Computer Equipment / Projector

Baracoda L (1D) Code 128 Settings, Enable/Disable Code 128/EAN, Set lengths for Code 128/EAN

Models: L (1D) LA (LASER)

1 49

Download 49 pages 27.3 Kb

Page 33

Image 33

Data Capture for Workforce in Motion

2.10.Code 128 Settings

2.10.1.Enable/Disable Code 128/EAN 128

To enable or disable Code 128/EAN 128, scan the appropriate barcode below.

Disable

Enable (*)

2.10.2.Set lengths for Code 128/EAN 128

Code 128/EAN 128 - barcode length - any length (*)

Code 128/EAN 128 - barcode length - minimum length = 6

RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.8

- 33 -

Page 33

Image 33

Baracoda L (1D), LA (LASER) manual Code 128 Settings, Enable/Disable Code 128/EAN, Set lengths for Code 128/EAN

Contents

Data Capture for Workforce in Motion RoadRunners Evolution -L 1D & -LA Laser Programming GuideBaracoda TM - November Data Capture SUMMARYfor Workforce in MotionData Capture 4. APPENDIX 2 - AIM SYMBOLOGY IDENTIFIERS STRUCTUREfor Workforce in MotionChanges to the original manual are listed below Revision HistoryData Capture for Workforce in Motion DocumentIntroduction Data Capture for Workforce in MotionRoadRunners Evolution -L 1D & -LA Laser - Programming Guide 1.1. General default settings 1. General ConfigurationData Capture for Workforce in Motion RoadRunners Evolution -L 1D & -LA Laser - Programming Guide1.2.1. Switch on delay 1.2. Baracoda advanced features1.2.2. Shutdown timers 1.2.3. Turn scanner OFFData Capture for Workforce in Motion 1.2.4. No data loss mode and Baracoda HeaderRoadRunners Evolution -L 1D & -LA Laser - Programming Guide Baracoda headerData Capture for Workforce in Motion 1.3. Reading ModeTrigger Aiming Trigger Mode« no duplicate scans » enabled + error signal « no duplicate scans » disabled« no duplicate scans » enabled + no decoding Data Capture for Workforce in MotionData Capture for Workforce in Motion 1.4. Operating ModeReal Time mode Real Time mode with No Data Loss option1.4.3. No Data Loss mode - Disable “ACK” beep 1.4.2. No Data Loss mode - Enable “ACK” beep1.4.1. Real Time mode 1.4.4. Real Time - Buffered data optionRestore last batch data 1.4.5. Batch modeRestore last batch + launch upload Data Capture for Workforce in MotionSlave mode by default 1.5. The different connection methodsData Capture for Workforce in Motion RoadRunners Evolution -L 1D & -LA Laser - Programming GuideACK beep off Beep level volume = HIGH Beep level Volume = LOW 1.6. Buzzer and Led SettingsData Capture for Workforce in Motion LED ON LED OFF Good read beep on Good read beep off ACK beep on1.7.1. Bluetooth name 1.7. Bluetooth settingsData Capture for Workforce in Motion RoadRunners Evolution -L 1D & -LA Laser - Programming GuideData Capture for Workforce in Motion 1.7.2. Sniff period settingsSniff period = 150ms Sniff period = 100ms Sniff period = 200ms Sniff period = 300ms Sniff period = 500ms1.7.4. RF Power emission settings 1.7.3. Security code PIN settingsDisable BT security code Enable BT security code Set device to Class1 power emission 20dBm1.8.1. Timestamp option 1.8. Data formatData Capture for Workforce in Motion RoadRunners Evolution -L 1D & -LA Laser - Programming GuideSTART Read « Set Timestamp » label Read intermediary label Read « END of config » label ENDCorresponding to the next digit to set for the Timestamp from Appendix NO Finished ? YESEnable data prefix Disable data prefix Enable data suffix 1.8.2. Data Prefix/SuffixDisable data suffix End Procedure to define Data/Barcode Prefix/SuffixData Capture for Workforce in Motion 1.8.3. Barcode Prefix/SuffixAIM Symbology identifier - not transmitted 1.8.4. AIM Symbology IdentifierAIM Symbology identifier - transmitted Data Capture for Workforce in Motion2.2. Enable/Disable All Symbologies 2.1. Decoder default settings2. Decoder Parameters 2.3. Set decoder barcode lengthSet barcode length END of config 2.4. VotingData Capture for Workforce in Motion Voting = Voting = Voting =Start - set min length Start - Set Max length End of config 2.5. Min/Max length per symbologyData Capture for Workforce in Motion RoadRunners Evolution -L 1D & -LA Laser - Programming Guide2.5.1. Symbology table 2.6. Codabar settings2.6.1. Enable/Disable Codabar Selected Symbology2.6.3. Codabar Check Digit Verification AIM recommendation 2.6.2. Codabar Start/Stop characters2.6.4. Set Lengths for Codabar Data Capture for Workforce in Motion2.7.1. Enable/Disable Code 2.7. Code 11 Settings2.7.2. Code 11 check digits verification 2.7.3. Transmit Code 11 check digits2.8.1. Enable/Disable Code 2.8. Code 39 settings2.8.2. Enable/Disable Code 39 Full ASCII 2.8.3. Code 39 Start/stop characters2.8.5. Code 39 Check Digit Verification 2.8.4. Accepted Code 39 characters2.8.6. Set lengths for Code Data Capture for Workforce in Motion2.8.7. Italian PharmaCode settings 2.9. Code 93 Settings2.9.1. Enable/Disable Code 2.9.2. Set Lengths for Code2.10.1. Enable/Disable Code 128/EAN 2.10. Code 128 Settings2.10.2. Set lengths for Code 128/EAN Data Capture for Workforce in MotionEnable GS transmission Disable GS Transmission 2.10.3. EAN 128 Group SeparatorEnd of configuration Data Capture for Workforce in Motion2.10.4. Enable/Disable AIM ID Transmission 2.11. Interleaved 2 of 5 Settings2.11.1. Enable/Disable Interleaved 2 of 2.11.2. Interleaved 2of 5 Check Digit2.12.1. Enable/Disable MSI 2.12. MSI Code Settings2.11.3. Set lengths for Interleaved 2 of 2.12.2. MSI Check Digit2.13.1. Enable/Disable Standard 2 of 2.13. Standard 2 of 5 Settings2.12.3. Set lengths for MSI 2.13.2. Standard 2 of 5 Check Digit2.14.1. Enable/Disable UPC/EAN 2.14. UPC/ EAN Settings2.13.3. Set lengths for Standard 2 of Data Capture for Workforce in Motion2.14.3. Transmit UPC-E Check Digit 2.14.2. Transmit EAN13 Check Digit2.14.4. Transmit EAN 8 Check Digit 2.14.5. Transmit UPC-A Check Digit2.14.6. Transmit UPC number system for UPC-E 2.14.7. UPC-A, UPC-E, EAN conversionsData Capture for Workforce in Motion 2.14.8. ISSN/ISBN settings 2.14.9. Add-on digiits settingsData Capture for Workforce in Motion 2.15.1. Enable/Disable GS1 DataBar 2.15. GS1 DataBar RSS 14 Settings2.15.2. GS1 DataBar 14 Check Digit Transmission 2.15.3. GS1 DataBar 14 Linkage flag Transmission2.16.1. Enable/Disable GS1 DataBar Limited 2.16. GS1 DataBar RSS Limited Settings2.16.2. GS1 DataBar Limited Check Digit Transmission 2.16.3. GS1 DataBar Limited Linkage flag TransmissionName Capital letters A-ZProgramming label Data Capture for Workforce in MotionData Capture for Workforce in Motion Small letters a-zName Programming labelData Capture for Workforce in Motion PonctuationName Programming labelData Capture for Workforce in Motion Decimal numbersName Programming labelName Programming label Control CharactersCR EOT ETX LF NUL SOH STX TAB Data Capture for Workforce in Motion4. APPENDIX 2 - AIM symbology identifiers structure Symbology CharacterData Capture for Workforce in Motion