Quick Start Guide - Barracuda NG Firewall 5.2
This Quick Start Guide will help you with the initial configuration of your Barracuda NG Firewall. It shows how to connect to your Barracuda NG Firewall, connect an Internet Service Provider, how to configure the firewall rule set to get a connection to the Internet, install your licenses and activate the unit.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
1. Network Deployment | ||||||||||||||||
|
| 3. Network Configuration | ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| Since every Barracuda NG Firewall is shipped with a default network configuration it is necessary | |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| to configure your personal computer accordingly. | |||
|
|
|
|
|
|
|
|
| Internet | Launch the network adapter configuration dialog of your MS Windows operating system and modify | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| the IPv4 configuration. | |||
|
|
|
|
|
|
|
|
|
| ISP Modem |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| PORT4 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| PORT1 |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
.200 |
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
| 192.168.200.0/24 |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
NG Admin | .100 |
|
|
|
|
|
2. Physical Connection | 4. Connect |
•Connect an AC power cord to the Barracuda NG Firewall.
Note: Immediately after connecting the power cord to the Barracuda NG Firewall (F10/ F10x/F20x), the appliance starts booting and loads the operating system.
•Either use the crossover network cable (red) to directly connect to the management port of the appliance or use the standard network cable (grey) and connect to the same network switch as the Barracuda NG Firewall.
The table below lists the default port configuration for certain appliance types. Models F10 to F30x have a pre configured WAN port to connect your ISP. Models F400 to F900 need to be configured manually.
Model | Management Port | WAN Port |
F10 | PORT1 | PORT4 |
F100 / F101 | PORT1 | PORT4 |
F200 / F201 | PORT1 | PORT4 |
F300 / F301 | PORT1 | PORT4 |
F400 | PORT1 |
|
F600 | PORT1 |
|
F800 | 1st port of left module |
|
F900 | MGMT |
|
Launch the NG Admin application located on the USB Thumb Drive shipped with your Barracuda NG Firewall. This application is used to manage your Barracuda NG Firewall.
Select Box, enter the default management IP address, the default user credentials, and click Login.
Management IP Address | Login | Password |
192.168.200.200 | root | ngf1r3wall |
