‰Adjusting plate assembly (Figure 11)

Make sure spline nut (item b) and bottom acorn nut (item c) are loose.

‰Initial head position (Figure 11)

yThe indicator plate assembly (item e) markings correspond to head position settings. Slide the secondary adjusting plate (item f) toward the rear of the burner until the number on the indicator plate corresponds to the initial head setting given in Table 4 for the desired firing rate.

yFigure 11 shows a typical example, with a head setting of 6.

yWhen the head position has been set, tighten the bottom acorn nut (item c) and the spline nut (item b).

‰Initial air settings (Figure 12)

yLoosen the screw holding the air adjusting plate (item m). Set the air to the desired rate. (The numbers on this plate correspond to the approximate firing rate settings given in Table 5.)

yRotate the air adjusting plate until the lower edge of the pointer is opposite the number from Table 5 corresponding to the desired firing rate.

yThis initial setting should be adequate for starting the burner. Tighten the screw to secure the adjusting plate. Once the burner is in operation, the air setting will be adjusted for best performance as discussed later in this manual.

yFollow the procedures given later in this manual for fine- tuning the air settings.

Figure 12 - Air damper assembly

l

Legend

hDamper label - position indicator for air adjustment plate k Damper indicator - permanently attached to damper

mAir adjusting plate - sets air position

lAir adjusting plate screw - locks plate position

Table 4 - Initial indicator adjustment plate settings (head position)

Approximate

Firing rate, gph

adjusting

 

 

Tube “A”

Tube “B”

plate setting

0

-

-

1

-

-

2

4.00

-

3

6.00

-

4

7.00

7.00

5

8.00

8.00

6

10.00

10.00

7 - 12

-

-

 

These settings are approximate, and

NOTE

can vary depending on actual job con-

 

ditions and overfire pressure.

Table 5 - Initial air adjusting plate settings (damper position)

Approximate

Firing rate, gph

head settings

Tube “A”

Tube “B”

0

4.00

4.00

1

4.50

7.50

2

5.00

8.00

3

6.00

9.00

4

7.00

10.00

5

7.50

-

6

8.00

-

7 - 10

10.00

-

 

 

 

 

These settings are approximate, and

NOTE

can vary depending on actual job con-

 

ditions and overfire pressure.

14

Form 6104 BCF10-R06

Page 13 Page 15
Page 14
Image 14
Beckett CF1000 manual ‰ Adjusting plate assembly Figure, ‰ Initial head position Figure, ‰ Initial air settings Figure
Page 13 Page 15

CF1000 specifications

The Beckett CF1000 is a cutting-edge, reliable, and efficient commercial burner designed for use in various heating applications. Known for its exceptional performance, it is increasingly popular among businesses and contractors looking for an effective solution to meet their heating needs.

One of the main features of the CF1000 is its advanced combustion technology. The burner is engineered to deliver optimal combustion efficiency, reducing emissions and enhancing fuel economy. This technology not only helps in lowering operational costs but also aligns with modern environmental regulations, making the CF1000 a responsible choice for energy-conscious businesses.

Another notable characteristic of the CF1000 is its ability to handle multiple fuel types, including oil and natural gas. This versatility allows users to choose the best fuel source for their specific application, contributing to operational flexibility. Additionally, the CF1000 is equipped with a modulation system that adjusts the burner output in response to demand, ensuring consistent heating without unnecessary energy consumption.

The CF1000 also stands out for its compact design, making it easy to install in various settings, whether in commercial buildings or industrial facilities. Its robust construction is designed to withstand demanding conditions, ensuring longevity and reliability. Moreover, the burner comes with advanced safety features, including flame monitoring and integrated shut-off systems, helping to prevent potential hazards during operation.

Ease of maintenance is another significant advantage of the Beckett CF1000. The design incorporates user-friendly service access points, allowing technicians to perform routine maintenance and inspections quickly and efficiently. This not only ensures optimal performance but also extends the lifespan of the burner.

Furthermore, the CF1000 is supported by Beckett's extensive customer service and technical support. Their commitment to quality and satisfaction means that users can rely on expert assistance whenever needed, ensuring peace of mind.

Overall, the Beckett CF1000 is a premier choice for those seeking a high-performance commercial burner. With its advanced combustion technology, versatile fuel options, compact design, and a wealth of safety features, it delivers reliable heating solutions suitable for a wide range of applications. Its ease of maintenance combined with robust support services makes the CF1000 an intelligent investment for any business prioritizing efficiency, safety, and reliability in their heating systems.
Top Page Image Contents