Section: Pre-installation Checklist

Test For Gas Pipe Leaks

○Flange mounting arrangement (Includes high- temperature gasket and /or fiber rope for pressure firing).

Leaking gas could result in asphyxiation, explosion, or fire hazard.

yThe gas supply piping must be absolutely leak-free.

yPressure test the gas piping with air that is at least three times greater than the gas pressure being used.

yVerify that there are no leaks before proceeding.

Clearances

With the burner installed in the appliance, there must be adequate space in front of and on the sides of the burner to allow access and operation. Verify that the clearance dimensions comply with local codes and with the appliance manufacturer’s recommendations.

Verify firing input range

Refer to appliance manufacturer’s instructions (if available) for the firing input range. Otherwise the maximum recommended firing range for the burner depends on the length and width of the firing chamber and the distance from the burner center to the chamber floor. Verify that the chamber dimensions are at least as large as the minimum values given in Figure 2. If the appliance dimensions are smaller, reduce the firing rate accordingly.

Dimensions shown are for cast iron sectional boilers with uptakes

between sections. For minimum dimensions of other furnace types consult R.W. Beckett Corporation.

Fuel gas supply

Verify that the gas supply piping complies with all applicable local codes and the latest edition of the National Fuel Gas Code ANSI Z223.1 (NFPA 54).

Insure that the supply gas pipe size is capable of providing at least the minimum pressure required to the burner gas train inlet at the burner’s full capacity rating. Refer to Table 1.

Flue vent system

The flue gas vent system must be in good condition and must comply with National Fuel Gas Code ANSI Z223.1 (NFPA 54) and all other applicable codes having jurisdiction for vent construction, capacity, and sizing.

Figure 2. Minimum Combustion Chamber Dimensions

Minimum Combustion

Chamber Dimensions (inches)

Electrical supply

Check the nameplate on the burner to verify that the power connections available are correct for the burner. Refer to Figure 1. All power must be supplied through fused disconnect switches and comply with the latest edition of National Electric Code NFPA 70 (Canada CSA C22.1) and all other local or applicable codes.

Verify burner components

○Burner model can be checked from burner carton or rating label on burner.

Input

Firing

Rate in

MBH

300-400

400-600

600-900

900-1200

Length

‘L’

18

22

26

30

Width ‘W’

12

14

16

18

Height

‘H’

12

14

16

18

Burner Head Centerline to floor ‘A’

6

7

8

9

6

Page 5 Page 7
Page 6
Image 6
Beckett CG10 manual Test For Gas Pipe Leaks, Clearances, Verify firing input range, Fuel gas supply, Flue vent system
Page 5 Page 7

CG10 specifications

The Beckett CG10 is a premium gas furnace that stands out in today's competitive heating market due to its innovative technology and reliable performance. Designed with efficiency and comfort in mind, the CG10 model ensures optimal heating solutions for residential spaces.

One of the most significant features of the Beckett CG10 is its impressive Annual Fuel Utilization Efficiency (AFUE) rating. With ratings often exceeding 90%, this furnace significantly reduces energy consumption and ensures cost-effective heating. This high-efficiency rating translates to lower utility bills and less environmental impact, making it a smart choice for eco-conscious homeowners.

The CG10 utilizes advanced combustion technology to ensure that fuel is burned effectively, maximizing heat generation while minimizing emissions. This innovative technology not only enhances the furnace's performance but also contributes to cleaner air, aligning with modern environmental standards.

A notable characteristic of the Beckett CG10 is its quiet operation. The unit is designed to operate with minimal noise, ensuring a comfortable living environment without disruptive sounds. This is particularly important for families and individuals who prioritize tranquility in their homes.

The furnace is built with durable materials, ensuring longevity and reliable performance over the years. Its construction adheres to strict industry standards, making the CG10 both robust and dependable. Regular maintenance is simplified thanks to its user-friendly design, which allows homeowners to access critical components easily.

Safety is a paramount concern in any heating system, and the Beckett CG10 does not disappoint. It comes equipped with multiple safety features, including flame sensors and safety shut-off mechanisms, ensuring peace of mind for users.

Additionally, the Beckett CG10 can be integrated with smart home technology, allowing homeowners to monitor and control their heating system remotely. This capability enhances convenience and provides further energy savings, as users can adjust their heating preferences from anywhere.

In summary, the Beckett CG10 gas furnace presents an ideal solution for homeowners seeking a blend of efficiency, durability, and advanced technology in their heating systems. Its high AFUE rating, quiet operation, and safety features make it a top choice for those prioritizing comfort and environmental responsibility.
Top Page Image Contents