Combustion Air Supply Information

See NFPA Standard 31 for complete details.

Appliances located in confined spaces: All confined spaces should have two (2) permanent openings; one near the top of the enclosure and one near the bottom of the enclosure. Each open- ing must have a free area of not less than one (1) square inch per 1,000 BTU’s per hour of the total input rating of all appliances within the enclosure. The openings should have free access to the build- ing interior, which should have adequate infiltration from the outside.

Exhaust fans and other air-using devices: Size air openings large enough to supply all air-using devices in addition to the minimum size required for combustion air. If there is any possibility of the equipment room developing a negative pressure due to exhaust fans, clothes dryers, etc., either pipe combustion air directly to the burner or provide a sealed enclosure for the burner and supply it with its own combustion air supply.

Direct/Sidewall Venting Application

!WARNING Connect Outside Air Duct to NX Adapter

Failure to install adapter properly could result in impaired combustion, appliance soot-up, puffback of smoke, and fire or asphyxiation hazards.

The outside air adapter must be installed by strictly following the kit installation instructions.

DO NOT attempt to install outside air piping without using the outside air adapter and instructions pro- vided.

Abundant fresh air is required for proper combus- tion.

For direct vent installations, follow instructions pro- vided with appliance and direct vent system. Out- side combustion air is required for direct venting.

When installing an NX outside air adapter (Beckett Part Number 1014U), refer to the instruction sheet supplied with the adapter. This kit allows combus- tion air to be piped directly to the burner. The NX outside air adapter kit may also be used for chim- ney vent applications that require outside combus- tion air.

Inspect/Prepare Installation Site

Fuel Line Installation

!CAUTION Do Not Use Teflon Tape

Damage to the pump could cause impaired burn- er operation, oil leakage and appliance soot-up.

Never use Teflon tape on fuel oil fittings.

Tape fragments can lodge in fuel line components and fuel unit, damaging the equipment and pre- venting proper operation.

Use oil-resistant pipe sealant compounds.

Route the fuel line through the opening in the bottom of the burner cover. Continuous lengths of heavy wall copper tubing are recommended. Always use flare fittings. Never use compression fittings.

Always install fittings in accessible locations. To avoid vibration noise, fuel lines should not run against the appliance or ceiling joists.

Fuel Line Valves and Filter

Install two high quality fusible-handle design shutoff valves in accessible locations on the oil supply line to comply with the NFPA31 Standard. Locate one close to the tank and the other close to the burner, upstream of the filter.

Install a generous capacity filter inside the building between the fuel tank shutoff valve and the burner, locating both the filter and the valve close to the burner for ease of servicing. Filter should be rated for 50 microns or less.

NOTICE

To further protect the fuel supply system and re- duce nozzle orifice plugging with firing rates below

0.75gph, a dual filtration system can be installed. This typically consists of a 50 micron primary filter, located near the fuel tank and a secondary filter rat- ed for at least 10 microns located near the burner.

RWB 6104 BNX R02

Page 5

Page 5
Image 5
Beckett NX manual Inspect/Prepare Installation Site, Combustion Air Supply Information, Direct/Sidewall Venting Application

NX specifications

Beckett NX is a cutting-edge oil burner that exemplifies energy efficiency and reliability in heating systems. Designed for both residential and commercial use, the Beckett NX system is engineered to optimize performance while minimizing energy consumption and emissions.

One of the standout features of the Beckett NX is its advanced combustion technology. It utilizes a precision-designed nozzle that ensures a fine mist of oil is atomized for optimal combustion. This not only enhances efficiency but also significantly reduces smoke and particulate emissions, making it an environmentally friendly choice in today’s market. The system is equipped with diagnostic capabilities that allow for easy troubleshooting, enabling users to monitor performance and quickly address any potential issues.

Another significant characteristic of Beckett NX is its compact design, which allows it to fit seamlessly into various heating systems without requiring extensive modifications. This makes it an ideal solution for both new installations and retrofitting existing systems. The burner is also designed for quiet operation, reducing noise levels compared to traditional models and ensuring a more comfortable indoor environment.

In terms of safety, the Beckett NX incorporates numerous features to ensure reliable operation. It includes a burner control that monitors flame stability and combustion quality, providing real-time feedback. With built-in safety mechanisms, such as a flame safeguard, the system minimizes risks associated with malfunctioning equipment.

The technology behind Beckett NX also embraces modern connectivity options. The burner can be integrated with smart home systems, allowing users to adjust settings remotely and monitor heating performance through dedicated apps or interfaces. This level of control empowers homeowners and business operators alike to enhance their heating efficiency further.

Finally, the Beckett NX is designed for longevity and ease of maintenance. Its modular components allow for straightforward access, simplifying routine servicing and reducing downtime. With a robust build quality that withstands the rigors of daily use, the Beckett NX promises durability and reliability for years to come.

In summary, Beckett NX stands out in the heating industry for its combination of advanced combustion technology, compact design, safety features, smart connectivity, and ease of maintenance. These characteristics make it a leading choice for those seeking an efficient and effective oil burner solution, ensuring homes and businesses stay warm while being mindful of environmental impact.