Network, Reset All, Current, System, Status | BenQ LW61ST, LX60ST

SYSTEM SETUP: Advanced me

6. INFORMATION menu

	Function	Description
		Wired LAN
		Wireless LAN
		Remote Desktop
		Broadcasting
		Projection Log In Code
	Network	See BenQ Network Projector Operation Guide for details.
	Network	AMX Device Discovery
	Settings	AMX Device Discovery
		When AMX Device Discovery is On, the projector can be detected
		by AMX controller.
		Mac Address
		Displays the mac address for this projector.
		The System limitation of 1:1 audio is Intel Pentium 4, 3.0G CPU, 1G RAM.

		Returns all settings to the factory preset values.
	Reset All	The following settings will still remain: Phase, H. Size, User 1, User 2, Color
	Settings	Space Conversion, Language, Projector Position, High Altitude
		Mode, Security Settings, DHCP, SSID, Remote Desktop and Baud
		Rate.
		Source
		Shows the current signal source.
		Picture Mode
		Shows the selected mode in the PICTURE menu.
	Current	Resolution
	Current	Shows the native resolution of the input signal.
	System	Color System
	Status	Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.
		Equivalent Light Source Hour
		Displays the number of hours the light source has been used.
		Firmware Version
		Shows the firmware version of your projector.

Operation 47

Image 47

BenQ LW61ST, LX60ST user manual Network, Reset All, Current, System, Status

Contents

LX60ST/LW61ST Table of contents Safety Instructions Important safety instructions 3000 m Feet This apparatus must be earthed Ceiling mounting the projector Introduction Projector features Shipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Keystone/Arrow buttons / Up Down Remote controlNetwork Setting Enters network setting directly Test Source selection buttons COMPUTER-1, COMPUTER-2 Numeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL + Operating the projector from Front Rear Remote control effective rangeReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front Table Obtaining a preferred projected image size Projection dimensions LW61ST Connection Connection Playing sound through the projector Connecting video source devicesConnecting audio Device About the microphone input Starting up the projector Operation Fine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Correcting keystone Highlight Using the menus Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a password Changing the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details About the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Adjusting Brilliant Color Fine-tuning the image quality in user modes 3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description Hiding the image To cancel the timer, perform the following stepsRemote paging operations Freezing the image Operating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keys Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volume To view your pictures as a slide show, follow these steps When viewing thumbnailsPresenting from a USB Reader Supported image formats Shutting down the projector Direct power offSetting Press Power or OFF a second time. The Power indicator light Basic Menu operationMenu system Main menu Sub-menu Options Advanced DNS Server Wired LAN Subnet MaskDefault Gateway IP Address Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save Settings Search System Setup Basic Function Description Quick AutoTimer Settings Lock AdjustmentsReceiver Panel Key Closed System Setup Advanced menu Function DescriptionBaud Rate Test Pattern System Reset AllNetwork Current Care of the projector Maintenance Extending light source life Setting Light Source Mode Selection as EconomicLight source information Getting to know the light source hour Status Message Timing of replacing the light sourceReplacing the light source Thermal events IndicatorsLight Status & Description Power events Troubleshooting Projector specifications Specifications Minimum installation requirements DimensionsWall mount installation Wxga Ceiling mount screw Minimum Ceiling Height mm = f + H + b + 60 + 274+ c Supported timing for PC input Timing chart KHz Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright