Adjusting the projected image | BenQ LW61ST, LX60ST instruction

Adjusting the projected image

Adjusting the projection angle

The projector is equipped 2 adjuster feet. These adjusters change the image height and projection angle. To adjust the projector:

Screw the adjuster feet to fine-tune the horizontal angle.

To retract the feet, screw the adjuster feet in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 22 for details.

Auto-adjusting the image

Do not look into the lens while the light source is on. The strong light from the light source may cause damage to your eyes.

Be careful when you press the quick- release button as it is close to the exhaust vent where hot air comes from.

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image clarity

Sharpen the image by rotating the focus ring.

Operation 21

Image 21

BenQ LW61ST, LX60ST user manual Adjusting the projected image, Adjusting the projection angle, Auto-adjusting the image

Contents

LX60ST/LW61ST Table of contents Safety Instructions Important safety instructions 3000 m Feet This apparatus must be earthed Ceiling mounting the projector Introduction Projector features Shipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Network Setting Enters network setting directly Test Remote controlSource selection buttons COMPUTER-1, COMPUTER-2 Keystone/Arrow buttons / Up Down Operating the Laser pointer VOLUME+/VOLUME- Adjusts the sound level MuteMIC/VOL + Numeric buttons Remote control effective range Replacing the remote control batteriesOperating the projector from Front Rear Choosing a location Positioning your projectorFront Table Front Ceiling Obtaining a preferred projected image size Projection dimensions LW61ST Connection Connection Connecting video source devices Connecting audioPlaying sound through the projector Device About the microphone input Starting up the projector Operation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarity Correcting keystone Highlight Using the menus Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTER If you forget the password Entering the password recall procedureChanging the password Disabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details About the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Adjusting Brilliant Color Fine-tuning the image quality in user modes 3D Color Management Setting the presentation timer Selection DescriptionTop-Left Bottom-Left Top-Right Bottom-Right Remote paging operations To cancel the timer, perform the following stepsFreezing the image Hiding the image Using the remote control To activate the High Altitude ModeLocking control keys Operating in a high altitude environment Adjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring Tone Presenting from a USB Reader When viewing thumbnailsSupported image formats To view your pictures as a slide show, follow these steps Setting Direct power offPress Power or OFF a second time. The Power indicator light Shutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Default Gateway Wired LAN Subnet MaskIP Address DNS Server Description of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description Teaching Timer System Setup Basic Function Description Quick AutoSettings Search Receiver AdjustmentsPanel Key Lock Baud Rate System Setup Advanced menu Function DescriptionTest Pattern Closed Network Reset AllCurrent System Care of the projector Maintenance Light source information Setting Light Source Mode Selection as EconomicGetting to know the light source hour Extending light source life Timing of replacing the light source Replacing the light sourceStatus Message Indicators Light Status & Description Power eventsThermal events Troubleshooting Projector specifications Specifications Dimensions Wall mount installationMinimum installation requirements Wxga Ceiling mount screw Minimum Ceiling Height mm = f + H + b + 60 + 274+ c Supported timing for PC input Timing chart KHz Supported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Limited warranty Warranty and Copyright informationCopyright Disclaimer