Adjusting the projected image | BenQ MX620ST guide

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1.Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2.Screw the rear adjuster foot to fine-tune the horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 20 for details.

2

1

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the quick- release button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

1.

Adjust the projected image to the

2.

Sharpen the image by rotating the

size that you need using the zoom

focus ring.

ring.

Operation 19

Image 19

BenQ MX620ST user manual Adjusting the projected image, Adjusting the projection angle, Auto-adjusting the image

Contents

MS619ST/MX620ST/MW621ST Table of contents Safety Instructions Important safety instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector features Shipping contents Front/upper side Rear/lower side Projector exterior view Controls and functions Remote control Replacing the remote control batteries Remote control effective range Front Ceiling Positioning your projectorChoosing a location Front Table Length Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm Diagonal MW621ST Connection Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearance Starting up the projector Operation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Correcting keystone Below is the overview of the OSD menu Using the menus Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a password Entering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio MS619ST/ MW621ST About the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Adjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature 3D Color Management Setting a preferred color temperature Resetting current or all picture modes Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the image Operating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keys Turning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound level To select Blackboard or Whiteboard Using the teaching templates Presenting from a USB Reader Shutting down the projector Direct power off Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Teaching Template Description Apply 3D Settings3D Sync Invert Mode Picture menu Function Description Picture ModeTemperature Reference Timer Fine Tuning 3D ColorReset Picture Settings Quick Auto Receiver System Setup Basic menu Function DescriptionOperation Remote Lamp System Setup Advanced menu Function Description HighAltitude Audio Current Reset AllStandby Network Care of the projector Maintenance Getting to know the lamp hour Lamp informationExtending lamp life Status Message Timing of replacing the lamp Replacing the lamp Maintenance Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp events Troubleshooting Projector specifications Specifications Ceiling mount installation Dimensions Supported timing for PC input Timing chart KHz Supported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright