Adjusting the sound, Using the test pattern | BenQ MX620ST guide

2.Press to highlight High Altitude Mode and press / select On. A confirmation message appears.

3.Highlight Yes and press MODE/ENTER.

Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over- heating. In cases like this, you should switch to High Altitude mode to solve these symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker(s). Be sure you have made a correct connection to the projector audio input. See "Connection" on page 16 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight Audio Settings and press MODE/ENTER. The Audio Settings page appears.

3.Highlight Mute and press / to select On.

If available, you can also press Mute on the remote control to toggle projector audio between on and off.

Adjusting the sound level

To adjust the sound level, press Volume +/- or / , or:

1.Repeat steps 1-2 above.

2.Press to highlight Volume and press / to select a desired sound level.

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.Repeat steps 1-2 above.

2.Press to highlight Power On/Off Ring Tone and press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

Using the test pattern

The projector is able to display the grid test pattern. It helps you adjust the image size and focus and check that the projected image is free from distortion.

To display the test pattern, open the OSD menu and go to the SYSTEM SETUP: Advanced > Test Pattern and press / to select On.

34 Operation

Image 34

BenQ MX620ST user manual Using the test pattern, Muting the sound, Adjusting the sound level

Contents

MS619ST/MX620ST/MW621ST Table of contents Important safety instructions Safety Instructions Safety Instructions 3000 m Feet Ceiling mounting the projector Projector features Introduction Shipping contents Projector exterior view Front/upper side Rear/lower side Controls and functions Remote control Remote control effective range Replacing the remote control batteries Front Table Positioning your projectorChoosing a location Front Ceiling Screen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size Length MW621ST Connection Connection Terminal name Terminal appearance Connecting video source devicesConnecting audio Best Operation Starting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystone Using the menus Below is the overview of the OSD menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTER Entering the password recall procedure If you forget the passwordChanging the password Switching input signal Disabling the password function Magnifying and searching for details Changing Color Space Selecting the aspect ratio About the aspect ratio MS619ST/ MW621ST Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menu Adjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature Setting a preferred color temperature 3D Color Management Resetting current or all picture modes Setting the presentation timerSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-Right Locking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environment Adjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or Whiteboard Presenting from a USB Reader Direct power off Shutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Teaching Template Description Apply 3D Settings3D Sync Invert Reference Picture menu Function Description Picture ModeTemperature Mode Settings Quick Auto Fine Tuning 3D ColorReset Picture Timer Remote System Setup Basic menu Function DescriptionOperation Receiver Audio System Setup Advanced menu Function Description HighAltitude Lamp Network Reset AllStandby Current Maintenance Care of the projector Getting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status Message Replacing the lamp Maintenance Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal events Troubleshooting Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input KHz Supported timing for Component-YPbPrinput Timing Supported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer