Manuals / BenQ / Computer Equipment / Projector

BenQ MX722 user manual Reset Lamp Timer, Change Password, Off/Audio in 1/Audio in 2/Audio L

Models: MX722

1 62

Download 62 pages 17.56 Kb

Page 39

Image 39

Main menu Sub-menu

Options

5. SYSTEM SETUP: Advanced

High Altitude Mode		On/Off
	Mute	On/Off
	Volume
Audio Settings	Microphone Volume
	Power On/Off	On/Off
	Ring Tone	On/Off
	Ring Tone
	Lamp Mode	Normal/Economic
Lamp Settings	Reset Lamp Timer
	Equivalent Lamp
Security	Change Password
Security	Change Security	Power On Lock
Settings	Change Security	Power On Lock
Settings	Settings	Web Control Lock
	Settings	Web Control Lock
Baud Rate		2400/4800/9600/14400/19200/
Baud Rate		38400/57600/115200
		38400/57600/115200

Test Pattern		On/Off
	Closed Caption	On/Off
Closed Caption	Enable	On/Off
Closed Caption	Enable
	Caption Version	CC1/CC2/CC3/CC4
	Network	On/Off
Standby	Microphone	On/Off
Standby	Monitor Out	On/Off
Settings	Monitor Out	On/Off
Settings	Audio Pass	Off/Audio in 1/Audio in 2/Audio L/
	Audio Pass	Off/Audio in 1/Audio in 2/Audio L/
	Through	R/HDMI
		Status

		DHCP
		IP Address
	Wired LAN	Subnet Mask

		Default Gateway
Network		DNS Server
Settings
Settings		Apply

	Projection Log In	On/Off
	Code

	AMX Device	On/Off
	Discovery	On/Off
	Discovery

	MAC Address
Reset All Settings

Operation 39

Page 39

Image 39

BenQ MX722 user manual Reset Lamp Timer, Change Password, Off/Audio in 1/Audio in 2/Audio L

Contents

User Manual MX722 Digital ProjectorTroubleshooting Table of contentsImportant safety MaintenanceSafety Instructions Important safety instructionsSafety Instructions Continued 3000 m 10000 feet 0 m 0 feet Ceiling mounting the projector Introduction Projector featuresShipping contents Standard accessoriesOptional accessories Projector exterior view Front/upper sideRear/lower side Projector Controls and functionsRemote control Operating the LASER pointer Remote control effective rangeReplacing the remote control batteries Choosing a location Positioning your projectorObtaining a preferred projected image size Projection dimensionsConnection Connecting video source devices Playing sound through the projectorConnecting audio About the microphone input Starting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imagePress Correcting keystoneMODE/ENTER Using the menusSecuring the projector Using a security cable lockUtilizing the password function Setting a password2. Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Switching input signalMagnifying and searching for details Selecting the aspect ratioThis function is only available when the HDMI-input port is in use 169 Scales an image so that it is About the aspect ratioYou could adjust the zoom setting or move Auto Scales an image proportionally to fitUsing Wall Color Selecting a picture modeOptimizing the image Adjusting Color Fine-tuning the image quality in user modesAdjusting Brightness Adjusting Contrast3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerRemote paging operations Freezing the imageTo cancel the timer, perform the following steps To activate the High Altitude Mode Hiding the imageLocking control keys Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundUsing the test pattern Adjusting the sound levelWhiteboard Using the teaching templatesLetter Formation Worksheet Coordinate Chart TeachingIf you dont respond in a few seconds, the message will disappear Direct power offShutting down the projector 3. Once the cooling process finishes, a Power OffMenu system Menu operation38 Operation 5 sec/10 sec/20 sec/30 sec/AlwaysSplash Screen Reset Lamp Timer Change PasswordOff/Audio in 1/Audio in 2/Audio L INFORMA TIONCurrent System Status Description of each menu See Selecting a Color Temperature on page 29 for details picture mode on page 28 for detailsSee Adjusting Contrast on page 29 for details See Adjusting Brilliant Color on page 29 for detailsthe menus on page 22 for details See Switching input signal on page 25 for detailsframe. See Setting the presentation timer on page 31 for details See Changing Color Space on page 25 for detailsthrough the power cord See Utilizing the password function on page 23 for details See Adjusting the sound on page 34 for detailsSee Setting Lamp Mode as Economic on page 49 for details See Resetting the lamp timer on page 53 for detailsnetwork function when it is in standby mode projector on page 17 for detailsSee BenQ Network Projector Operation Guide for details Current 6. INFORMATION menuFunction DescriptionCare of the projector MaintenanceCleaning the lens Cleaning the projector caseLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Install a new lamp for optimal performance. If thewhenever you notice that the brightness level has Replacing the lamp 7. Use the handle to slowly pull the lamp out of the projector Resetting the lamp timer Status & Description IndicatorsPower events LightTroubleshooting Please see Entering the password recallprocedure on page 24 for details Projector specifications Specifications339 238 120.5 DimensionsCeiling mount installation SpecificationsTiming chart Supported timing for PC inputPixel Pixel Supported timing for HDMI HDCP input60 Specifications Supported timing for Component-YPbPr inputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty Copyright

Reset Lamp Timer

Change Password

Off/Audio in 1/Audio in 2/Audio L/