Manuals / Billion Electric Company / Computer Equipment / Network Router

Billion Electric Company 7402 Factory Default Settings, Username and Password, Web Interface

Models: 7402

1 123

Download 123 pages 44.82 Kb

Page 20

Factory Default Settings

Billion BIPAC-7402 / 7402W (Wireless) ADSL VPN Firewall Router with 3DES Accelerator

Factory Default Settings

Before configuring your, you need to know the following default settings.

Web Interface:

Username: admin

Password: admin

LAN Device IP Settings:

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site:

PPPoE

DHCP server:

DHCP server is enabled.

Start IP Address: 192.168.1.100

IP pool counts: 100

Username and Password

The default username and password are “admin” and “admin” respectively.

If you ever forget the password to log in, you may press the RESET button up to 6 seconds to restore the factory default settings.

Attention

LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below.

LAN Port

WAN Port

	IP address		192.168.1.254		The PPPoE function is enabled
	IP address		192.168.1.254		The PPPoE function is enabled
					to automatically get the WAN
	Subnet Mask		255.255.255.0		to automatically get the WAN
	Subnet Mask		255.255.255.0		port configuration from the ISP,
	DHCP server function		Enabled		but you have to set the
					but you have to set the
					username and password first.
	IP addresses for		100 IP addresses continuing from
	distribution to PCs		192.168.1.100 through 192.168.1.199
					14
	Chapter 3: Basic Installation

Image 20

Billion Electric Company 7402 Factory Default Settings, Username and Password, LAN and WAN Port Addresses, Web Interface

Contents

Version Release 1.54c Wireless ADSL VPN Firewall Router with 3DES AcceleratorBIPAC-7402 / 7402W User’s ManualPage CHAPTER 2 INSTALLING THE ROUTER CHAPTER 3 BASIC INSTALLATIONCHAPTER 1 INTRODUCTION Table of ContentsTable of Contents Q UICK S TARTS AVE C ONFIGURATION TO F LASH P ROBLEMS STARTING UP THE ROUTERP ROBLEMS WITH THE WAN I NTERFACE P ROBLEMS WITH THE LAN I NTERFACEPage Features Wireless Ethernet 802.11b 7402W OnlyFast Ethernet Switch Quick Installation WizardDynamic Host Configuration Protocol DHCP client and server Network Address Translation NATFirewall Domain Name System DNS relayFirmware Upgradeable Static and RIP1/2 RoutingSimple Network Management Protocol SNMP Web based GUIBIPAC-7402 / 7402W ADSL Router Application 74027402W Figure 1.1 Application Diagram ofPackage Contents Chapter 2 Installing the RouterImportant note for using the BIPAC-7402W ADSL Router The Front LEDs MeaningPPP / MAIL ADSL LAN Port 1XPower Switch PWR RESET LAN 1X passwordThe Rear Ports PortCabling Chapter 3 Basic Installation Connecting your routerConfiguring PCs in Windows For Windows XP2. Double-click Local Area Connection. See Figure 4. Select Internet Protocol TCP/IP and click Properties. See FigureFor Windows 2. Double-click Local Area “LAN” Connection. SeeFigure 3.7 TCP / IP Figure 3.8 IP Address & DNS Configuration 4. Select Internet Protocol TCP/IP and click Properties. See FigureThen select the DNS Configuration tab. See Figure Select the Disable DNS radio button and click OK tofinish the configuration For Windows 98 / MEFor Windows NT4.0 2. Select TCP/IP Protocol and click Properties. SeeFactory Default Settings Username and PasswordLAN Device IP Settings ISP setting in WAN siteInformation from your ISP PPPoE PPPoA RFC1483 Bridged RFC1483 Routed IPoAConfiguring with your Web Browser Figure 3.14 User namd & Password Prompt WidonwQuick Start Chapter 4 ConfigurationSave Config to FLASH Status ARP TableRIP Routing Table Routing TableRouting Table DHCP Table Leased TableExpired Table Permanent TablePPTP Status IPSec Status L2TP Status Email StatusError Logging Event LogNAT Sessions UPnP PortmapQuick Start Click Start to begin scanning for encapsulation types offered by your ISP. If the scan is successful you will then be presented with a list of supported options Configuration LAN Local Area NetworkEthernet LAN, WAN, System, Firewall, VPN, QoS, Virtual Server and AdvancedWireless 7402W Only ESSID BroadcastWireless Security 7402W Only WPA Pre-Shared KeyPage Port Setting DHCP Server Click Apply to enable this function Chapter 4 ConfigurationWAN Wide Area Network RFC 1483 Routed Connections PPPoE Connections Advanced Options PPPoE ConnectionGive DNSto Relay Controls whether the PPP Internet Protocol Control Protocol IPCP can request the DNS server IP address for a remote PPP peer. Once IPCP has discovered the DNS server IP address, it automatically gives the address to the local DNS relay so that a connection can be established RFC 1483 Bridged Connections All Ip PppoePPPoA Routed Connections Advanced Options PPPoA ConnectionChapter 4 Configuration IPoA Routed Connections Page ADSL System Time ZoneRemote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control Chapter 4 Configuration URL Filter To block PCs on your local network from unwanted websitesGeneral Settings Packet Filter Chapter 4 ConfigurationChapter 4 Configuration Port FiltersTable 1 Pre-defined Port Filter Address Filters Configuring Packet Filter Click Port FiltersClick Delete 4. Click Add TCP FilterClick Add TCP Filter Input HTTP port number Select “Allow”HTTP inbound & outbound application Intrusion Detection Block DurationTable 2 Hacker attack types recognized by the IDS Intrusion NameDetect Parameter Blacklist Type of Block DurationMAC Address Filter URL Filter Restrict URL Features Log information can be seen in the Status - Event Log after enabling Firewall LogChapter 4 Configuration VPN Virtual Private Networks PPTPRemote Access PPTP Connection Click Apply after changing settings LAN to LAN PPTP Connection Click Apply after changing settings Chapter 4 Configuration IPSecClick Create to configure a new IPSec VPN connection Configure a new VPN Connection LocalRemote ProposalMD5 A one-way hashing algorithm that produces a 128−bit hash Remote ID Advanced OptionLocal ID L2TP Chapter 4 ConfigurationRemote Access L2TP Connection IPSec Enable for enhancing your LT2P VPN security LAN to LAN L2TP Connection IPSec Enable for enhancing your LT2P VPN security Example Configuring a Remote Access PPTP VPN Dial-in Connection Dial-in Configuring PPTP VPN in the OfficeFunction DescriptionExample Configuring a Remote Access PPTP VPN Dial-out Connection Dial-out Configuring the PPTP VPN in the OfficeFunction DescriptionExample Configuring a LAN-to-LAN PPTP VPN Connection Description Configuring PPTP VPN in the Head OfficeFunction Description Configuring PPTP VPN in the Branch OfficeFunction Example Configuring a IPSec LAN-to-LAN VPN Connection Table 3 Network Configuration and Security Plan192.168.0.0/24 69.1.121.30 192.168.1.0/24 69.1.121.3 12345678 Tunnel mode ESPMD5 with AESConfiguring IPSec VPN in the Head Office FunctionDescription IP address of the head office router in WAN sideConfiguring IPSec VPN in the Branch Office FunctionDescription IP address of the head office router in WAN sideChapter 4 Configuration Example Configuring a Remote Access L2TP VPN Dial-in ConnectionDial-in Description Configuring L2TP VPN in the OfficeFunction Chapter 4 Configuration Example Configuring a Remote Access L2TP VPN Dial-out ConnectionDial-out Description Configuring the L2TP VPN in the OfficeFunction Example Configuring your Router to Dial-in to the Server Chapter 4 ConfigurationExample Configuring LAN-to-LAN L2TP VPN Connection Chapter 4 ConfigurationDescription Configuring L2TP VPN in the Head OfficeFunction Description Configuring L2TP VPN in the Branch OfficeFunction QoS Quality of Service Prioritization HighIP Throttling Virtual Server “Port Forwarding” Table 4 Well-know and registered PortsPort Number ProtocolNEWS Network News Transfer Protocol In addition to specifying the port number to be used, you will also need to specify the protocol used. The protocol used is determined by the particular application. Most applications will use TCP or UDP, however you can specify other protocols using the drop-down Protocol menu. Setting the protocol to “all” will cause all incoming connection attempts using all protocols on all port numbers to be forwarded to the specified IP address Advanced Static RoutingDynamic DNS Check Emails Device Management Embedded Web ServerSNMP Universal Plug and Play UPnPSNMP V1 and SNMP Version SNMPv2c and SNMPv3 From RFC 1213 MIB-IIFrom RFC1650 EtherLike-MIB From RFC 1493 Bridge MIBFrom RFC 1472 PPP/Security MIB From RFC 1473 PPP/IP MIBFrom RFC 1474 PPP/Bridge MIB From RFC1573 IfMIBSave Configuration to Flash Chapter 4 ConfigurationLogout Chapter 5 Troubleshooting Problems starting up the routerProblems with the WAN Interface ProblemProblems with the LAN Interface ProblemCorrective Action Frequent loss of ADSL linesync disconnectionsWORLDWIDE APPENDIX A Product Support and Contact InformationContact Billion AUSTRALIA