Configuration, Ethernet | Billion Electric Company 7402 guide

Configuration

Billion BIPAC-7402 / 7402W (Wireless) ADSL VPN Firewall Router with 3DES Accelerator

Configuration

When you click this item, you get following sub-items to configure the ADSL router.

LAN, WAN, System, Firewall, VPN, QoS, Virtual Server and Advanced

These functions are described below in the following sections.

LAN (Local Area Network)

There are four items within the LAN section: Ethernet, Wireless, Wireless Security, Port Setting and DHCP Server.

Ethernet

The router supports two Ethernet IP addresses in the LAN, and two different LAN subnets through which you can access the Internet at the same time. Users usually only have one subnet in their LAN, so there is no need to configure a Secondary IP address. The default IP address for the router is 192.168.1.254.

RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

The Subnet mask of Secondary IP Address depends on the setting of Primary IP Address.

28

Chapter 4: Configuration

Image 34

Billion Electric Company 7402 user manual Configuration, LAN Local Area Network, Ethernet

Contents

BIPAC-7402 / 7402W Version Release 1.54cWireless ADSL VPN Firewall Router with 3DES Accelerator User’s ManualPage CHAPTER 1 INTRODUCTION CHAPTER 2 INSTALLING THE ROUTERCHAPTER 3 BASIC INSTALLATION Table of Contents Table of Contents Q UICK S TART P ROBLEMS WITH THE WAN I NTERFACE S AVE C ONFIGURATION TO F LASHP ROBLEMS STARTING UP THE ROUTER P ROBLEMS WITH THE LAN I NTERFACEPage Fast Ethernet Switch FeaturesWireless Ethernet 802.11b 7402W Only Quick Installation Wizard Firewall Dynamic Host Configuration Protocol DHCP client and serverNetwork Address Translation NAT Domain Name System DNS relay Simple Network Management Protocol SNMP Firmware UpgradeableStatic and RIP1/2 Routing Web based GUI 7402W BIPAC-7402 / 7402W ADSL Router Application7402 Figure 1.1 Application Diagram of Important note for using the BIPAC-7402W ADSL Router Chapter 2 Installing the RouterPackage Contents PPP / MAIL The Front LEDsMeaning ADSL LAN Port 1X The Rear Ports Power Switch PWR RESET LAN 1Xpassword Port Cabling Chapter 3 Basic Installation Connecting your router 2. Double-click Local Area Connection. See Figure Configuring PCs in WindowsFor Windows XP 4. Select Internet Protocol TCP/IP and click Properties. See Figure Figure 3.7 TCP / IP Figure 3.8 IP Address & DNS Configuration For Windows2. Double-click Local Area “LAN” Connection. See Figure 3.5 LAN Area Connection finish the configuration Then select the DNS Configuration tab. See FigureSelect the Disable DNS radio button and click OK to For Windows 98 / ME For Windows NT4.0 2. Select TCP/IP Protocol and click Properties. See LAN Device IP Settings Factory Default SettingsUsername and Password ISP setting in WAN site Information from your ISP PPPoE PPPoA RFC1483 Bridged RFC1483 Routed IPoA Configuring with your Web Browser Figure 3.14 User namd & Password Prompt Widonw Save Config to FLASH Chapter 4 ConfigurationQuick Start Status ARP Table Routing Table Routing TableRIP Routing Table Expired Table DHCP TableLeased Table Permanent Table PPTP Status IPSec Status L2TP Status Email Status Error Logging Event Log NAT Sessions UPnP Portmap Quick Start Click Start to begin scanning for encapsulation types offered by your ISP. If the scan is successful you will then be presented with a list of supported options Ethernet ConfigurationLAN Local Area Network LAN, WAN, System, Firewall, VPN, QoS, Virtual Server and Advanced Wireless 7402W Only ESSID Broadcast Wireless Security 7402W Only WPA Pre-Shared KeyPage Port Setting DHCP Server Click Apply to enable this function WAN Wide Area Network RFC 1483 Routed Connections PPPoE Connections Advanced Options PPPoE Connection Give DNSto Relay Controls whether the PPP Internet Protocol Control Protocol IPCP can request the DNS server IP address for a remote PPP peer. Once IPCP has discovered the DNS server IP address, it automatically gives the address to the local DNS relay so that a connection can be established RFC 1483 Bridged Connections All Ip Pppoe PPPoA Routed Connections Advanced Options PPPoA Chapter 4 Configuration IPoA Routed Connections Page ADSL System Time Zone Remote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control URL Filter To block PCs on your local network from unwanted websites General Settings Packet Filter Port Filters Table 1 Pre-defined Port Filter Address Filters Configuring Packet Filter Click Port Filters Click Add TCP Filter Click Delete4. Click Add TCP Filter Input HTTP port number Select “Allow” HTTP inbound & outbound application Intrusion Detection Block Duration Detect Parameter Blacklist Table 2 Hacker attack types recognized by the IDSIntrusion Name Type of Block Duration MAC Address Filter URL Filter Restrict URL Features Firewall Log Log information can be seen in the Status - Event Log after enabling VPN Virtual Private Networks PPTP Remote Access PPTP Connection Click Apply after changing settings LAN to LAN PPTP Connection Click Apply after changing settings IPSec Click Create to configure a new IPSec VPN connection Remote Configure a new VPN ConnectionLocal Proposal MD5 A one-way hashing algorithm that produces a 128−bit hash Local ID Advanced OptionRemote ID L2TP Remote Access L2TP Connection IPSec Enable for enhancing your LT2P VPN security LAN to LAN L2TP Connection IPSec Enable for enhancing your LT2P VPN security Example Configuring a Remote Access PPTP VPN Dial-in Connection Dial-in Configuring PPTP VPN in the Office Function Description Example Configuring a Remote Access PPTP VPN Dial-out Connection Dial-out Configuring the PPTP VPN in the Office Function Description Example Configuring a LAN-to-LAN PPTP VPN Connection Configuring PPTP VPN in the Head Office Configuring PPTP VPN in the Branch Office 192.168.0.0/24 69.1.121.30 192.168.1.0/24 69.1.121.3 12345678 Example Configuring a IPSec LAN-to-LAN VPN ConnectionTable 3 Network Configuration and Security Plan Tunnel mode ESPMD5 with AES Configuring IPSec VPN in the Head Office IP address of the head office router in WAN side Configuring IPSec VPN in the Branch Office Example Configuring a Remote Access L2TP VPN Dial-in Connection Dial-in Configuring L2TP VPN in the Office Example Configuring a Remote Access L2TP VPN Dial-out Connection Dial-out Configuring the L2TP VPN in the Office Example Configuring your Router to Dial-in to the Server Example Configuring LAN-to-LAN L2TP VPN Connection Configuring L2TP VPN in the Head Office Configuring L2TP VPN in the Branch Office QoS Quality of Service Prioritization High IP Throttling Port Number Virtual Server “Port Forwarding”Table 4 Well-know and registered Ports Protocol NEWS Network News Transfer Protocol In addition to specifying the port number to be used, you will also need to specify the protocol used. The protocol used is determined by the particular application. Most applications will use TCP or UDP, however you can specify other protocols using the drop-down Protocol menu. Setting the protocol to “all” will cause all incoming connection attempts using all protocols on all port numbers to be forwarded to the specified IP address Advanced Static Routing Dynamic DNS Check Emails Device Management Embedded Web Server SNMP V1 and Universal Plug and Play UPnPSNMP From RFC1650 EtherLike-MIB SNMP Version SNMPv2c and SNMPv3From RFC 1213 MIB-II From RFC 1493 Bridge MIB From RFC 1474 PPP/Bridge MIB From RFC 1472 PPP/Security MIBFrom RFC 1473 PPP/IP MIB From RFC1573 IfMIB Save Configuration to Flash Logout Problems with the WAN Interface Chapter 5 TroubleshootingProblems starting up the router Problem Frequent loss of ADSL linesync disconnections Problems with the LAN InterfaceCan’t ping any PCs on the LAN Contact Billion AUSTRALIA APPENDIX A Product Support and Contact InformationWORLDWIDE