Raking OPERATION-SPRING Reel

PR & OS Owner’s Manual

NOTE: Must have the spring tine reel assembly (350354) for this operation.

MOW: Mow the lawn to it’s normal cut height. Tall grass will not leave a manicured look when the dethatching job is complete.

DRY: Be sure grass is relatively dry. Wet conditions can cause increased damage to healthy grass.

SET DEPTH: With engine off, set the raking depth so that the spring tines are just above touching the

flat surface (i.e. driveway, or sidewalk) the units height is being adjusted on. NOTE: Allowing the spring tines to have substantial contact with the ground will cause premature wear and failure of the spring tines.

START ENGINE: See page 9 for further instruction.

ENGAGE TINES: Pull back on the bail on the operators handle. NOTE: When engaging the spring tines in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the spring tines. Slowly lower the unit into the turf. RAKE: Rake a small test area and examine the results. Thatch should be removed and deposited on top of the healthy grass. If excessive damage occurs to healthy grass, adjust the spring tine depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during operation the spring tine depth is set too low.

REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn. This thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection and removal of the thatch.

VERTI-CUTTING OPERATION

NOTE: Must have the slicing reel assembly (350113) for this operation.

MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)

DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.

SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface (i.e. driveway, or sidewalk).

START ENGINE: See Page 9.

ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the turf.

SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should be removed and deposited on top of the healthy grass. Grass runners should be cut and ready for removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during operation the blade depth is set too low.

REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection and removal of the thatch/stems.

OVERSEEDING OPERATION

NOTE: Must have the slicing reel assembly (350113) for this operation.

MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)

DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.

SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft2 [4.5

kg. per 93 m2 ])

SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm) below a flat surface (i.e. driveway, or sidewalk).

START ENGINE: See Page 9.

ENGAGE CLUTCH: Pull back on the bail on the operators handle. NOTE: When engaging the clutch in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the clutch. Slowly lower the unit into the turf. SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during operation the blade depth is set too low.

WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to the seed suppliers directions.

Part No 350324

Form No F021108D

PR600S, OS551H, OS600S, PR500HT, OS551 specifications

The Billy Goat brand is renowned for its durable and efficient outdoor power equipment, particularly in the realm of leaf blowers, vacuums, and brush cutters. Among the standout offerings are the OS551H, PR600S, OS551, OS600S, and PR500HT models, each designed to tackle specific tasks with efficiency and ease.

The OS551H is a powerful outdoor clean-up tool featuring a robust Honda engine that ensures high performance and reliability. With its innovative design, this model offers excellent maneuverability and is perfect for tackling large areas with leaves and debris. The OS551H also boasts a debris management system that allows users to effectively collect and mulch leaves, making it a favorite among landscaping professionals.

The PR600S is a versatile and user-friendly power rake. It is built to effortlessly remove thatch and promote healthy lawn growth. With adjustable height settings, the PR600S accommodates various turf types and conditions. Its powerful engine and durable construction make it an ideal choice for homeowners and professionals seeking to enhance lawn health and aesthetics.

Meanwhile, the OS551 model features a robust blower designed for clearing debris effectively. Its compact design allows for easy operation in tight spaces, making it suitable for both residential and commercial use. Additionally, it employs advanced noise-reduction technology, ensuring quieter operation while still maintaining powerful air output.

The OS600S is an upgraded version of its predecessor with an enhanced airspeed capacity, allowing it to move large volumes of air efficiently. This model is particularly advantageous for heavy-duty clean-up tasks, such as clearing thick leaves or debris after storms. The ergonomic design ensures operator comfort during extended use, reducing fatigue and enhancing productivity.

Lastly, the PR500HT is a high-performance power rake optimized for heavy-duty lawn care. It incorporates advanced features such as adjustable rake depth and high-speed operation, allowing it to tackle thick thatch effectively. The PR500HT is designed for both ease of use and longevity, making it a preferred tool among lawn care enthusiasts and professionals alike.

In conclusion, Billy Goat’s OS551H, PR600S, OS551, OS600S, and PR500HT models reflect a commitment to quality, efficiency, and user-friendliness. Whether for residential or commercial applications, these machines offer the technology and durability needed to meet various outdoor maintenance challenges.

Billy Goat OS600S Raking OPERATION-SPRING Reel, VERTI-CUTTING Operation, Overseeding Operation

Models: PR600S OS551H OS600S PR500HT OS551 PR550T