9GENERAL SAFETY

For your safety and the safety of others, these

directions should be followed:

Do not operate this machine without first reading owner's manual and engine manufacturer's manual.

Use of Ear Protection is recommended while operating this machine.

Use of Eye and breathing protection is recom- mended when using this machine, especially in

dry and dusty conditions.

·DO NOT place hands or feet inside air intake opening, near exhaust outlet or near any moving parts.

·DO NOT start engine without deflector attached to exhaust outlet. ·DO NOT direct exhaust outlet toward any bystanders.

·DO NOT operate this equipment without first inspecting work area.

·DO NOT operate this equipment during excessive vibration. ·DO NOT start engine without housing front plate attached. ·DO NOT operate this machine on slopes greater than 20%. ·DO NOT blow any hot or burning debris, or any toxic or explosive material.

·DO NOT allow children to operate this equipment.

10ASSEMBLY

Read all safety and operating instructions before assembling or starting this unit.

PUT OIL IN ENGINE BEFORE STARTING

Your Billy Goat is shipped from the factory in one carton, completely assembled except for the upper handle assembly, handle brace, plate deflector and throttle control.

1.Install front exhaust wire loop(Item 55) across upper handle and slide wire loop to lowest possible position on upper handle.

Install upper handle (Item 28), to preassembled lower handle (item 29) by sliding the upper over and down the outside of the lower handle. Pull recoil handle from the engine and place it between rope guides (Item 13). Using screw (Item 22) & lock nut (Item 32) to install upper handle to lower handle. NOTE: Install rope guide on the left hand side for the Honda unit and right hand side for the Briggs & Stratton unit (See fig below for the pictorial

example). Finish installing the other side of the upper handle assembly using screw (Item 17) and lock nut (Item 32).

2. Install front of handle brace (Item 30), to blower housing using

one screw (Item 17), one washer (Item 58) and one lock nut (item 32). Install rear of handle brace (item 30) to upper handle vibration mounts using two lock nuts (item 32). Hand tighten only.

3. Securely tighten all hardware listed above in steps 1 thru 2.

4.Remove four lock nuts from the front plate and use them to attach the front wheel bracket (Item 27). Using spacer (Item 18), washer (Item 19), and Lock Nut (Item 16) to attach Front wheel (Item 23) onto the front wheel bracket.

5.Connect spark plug wire.

11PACKING CHECKLIST

These items should be included in your carton. If any of these parts are missing, contact your dealer.

NOTE:Preassemble front exhaust wire loop(Item 55) across upper handle before attaching upper handle to lower handle.

Boxing Checklist

Check

 

Front Exhaust

 

 

 

 

Director

 

430315

Check

 

Wire Loop

 

 

 

 

Front Exhaust

 

430336

Check

 

Handle Upper

 

 

 

 

Assembly

 

 

400957

Check

 

 

Handle Brace

 

 

 

 

400951

Check

Parts Bag

&Literature Assy

Check

Parts Bag & Literature Assy 430334

Per Model

Engine

Manual

Per Model

Check

Briggs & Stratton 10 HP

Honda 8 & 11 HP

Denotes parts found in

Parts Bag Assembly (shown on page 4).

Check

Check

Bracket Front Wheel 430270

Front Wheel 430271

Part No. 430316

Page 3 of 12

Form No. F083100A

Page 2 Page 4
Page 3
Image 3
Billy Goat QB884H, QB1004, QB1104H specifications General Safety, Assembly, Packing Checklist
Page 2 Page 4

QB1104H, QB1004, QB884H specifications

The Billy Goat QB884H, QB1004, and QB1104H are professional-grade walk-behind leaf blowers designed for optimal performance, efficiency, and ease of use. These models stand out in the market due to their rugged construction and advanced technological features, making them ideal for both residential and commercial applications.

The QB884H is equipped with a powerful Honda engine, delivering impressive performance and reliability. Its 8-blade impeller significantly increases air velocity, allowing for efficient removal of leaves and debris. The lightweight design enhances maneuverability, making it easy to operate for extended periods. It also features a unique ergonomic handle that reduces operator fatigue and improves control during use.

Next in line, the QB1004 offers a step up in power with its robust engine, providing superior airflow and improved clearing capacity. This model integrates an innovative debris management system, which reduces clogging and enhances overall efficiency. The unit’s adjustable airflow speed allows users to customize performance depending on the size and density of the debris, making it an excellent choice for various tasks. Additionally, its quick-release nozzle design makes switching between tasks seamless.

The QB1104H is the heavy-duty option in this lineup, boasting the most powerful engine among the three. It is engineered for commercial use, capable of tackling the toughest jobs. The advanced overhead valve design is specifically calibrated for maximum torque at lower RPM, ensuring higher efficiency and lower fuel consumption. The QB1104H includes an easy-start system for smoother operation and reduces the effort needed to power up the machine.

All three models feature a durable, weather-resistant construction that ensures longevity even in challenging conditions. Maintenance is straightforward, with accessible components allowing easy serviceability. The highlighted safety features include an automatic engine shut-off that activates when the handle is released, ensuring operator safety.

In summary, the Billy Goat QB884H, QB1004, and QB1104H deliver exceptional performance with innovations that enhance usability, making them valuable tools for any landscaping professional or property owner. Their combination of power, efficiency, and ergonomic design sets them apart, demonstrating why they are highly regarded in the industry. Whether tackling residential lawns or large commercial properties, these models are equipped to meet diverse landscaping needs.
Top Page Image Contents