KVSP/TKVSP Owner’s Manual

BELT TENSION ADJUSTMENT

DO NOT ADJUST WHILE THE MACHINE IS RUNNING!

1.Wait for engine to cool and disconnect spark plug.

2.Remove the transmission cover

3.Using two ½” wrenches loosen the two nuts on the cable that connects to the idler arm.

4.The setting of the tension on the belt is controlled by the distance on the threads of the cable. To loosen tension, move the position towards the end of the threads and in the opposite direction to tighten.

5.Check the travel of the idler arm by engaging the bail, which the drive should start to engage when the bail is 2 ½ inches away from the handle. The spring, at a relaxed state should be 1.5 inches long on the coil, and when the bail is in contact with the handle it should be 1.75 inches long. If the belt is too tight it can cause premature failure and if it is too loose it can come off of the pulley.

6.When satisfied with the position, place the transmission cover back into place and secure. Then run the machine to make sure the transmission is engaging properly. If the drive will not engage or will not disengage repeat the previous steps.

Spring length 1.5”- resting 1.75”- bail at handle

BELT REPLACEMENT

1.Wait for engine to cool and disconnect spark plug.

2.Drain fuel and oil from the engine.

3.Remove bag, quick release and upper handle. Do not kink, stretch, or break control cables, control housings, or end fittings while removing handles.

4.Remove the transmission cover, idler pulley, transmission and the belt from the transmission.

5.Remove the transmission plate and the housing top plate by removing bolts around outside of housing.

6.Leaving engine fastened to top plate, turn it upside down so the impeller is on top.

7.Remove impeller bolt and lock washer.

8.Lift impeller upward. If impeller slides freely, proceed to (step 10).

9.If the impeller does not loosen, obtain a 3/4-16x3” (Billy Goat part #440192) or longer bolt. Thread bolt by hand into nut until bolt rests against the shaft. Tighten the bolt slowly, which will pull the impeller away from the shaft, remove impeller from shaft. Using a penetrating oil can help loosen a stuck impeller.

10.Place the new belt on the shaft.

11.Using a new impeller bolt and lockwasher, reinstall new impeller in reverse order.

12.Tighten impeller bolt. Torque impeller bolt to 33-40 Ft. Lbs. (44-54 N.m) (see item 45 on page 15).

13.Make sure the belt is in the groove on the impeller and feed it through the hole in the top plate.

14.Reinstall engine onto housing in reverse order of removal make sure the belt is inside the two fingers on the belt plate and that the belt is on the transmission pulley before securing the transmission.

15.Gas and oil.

16.Reconnect spark plug wire.

Part No 891058

13

Form No F030309B

 

 

Page 12 Page 14
Page 13
Image 13
Billy Goat KV600SPFB, TKV650SPHFB owner manual Belt Tension Adjustment, Belt Replacement
Page 12 Page 14

TKV650SPHFB, KV650SPHFB, KV600SPFB specifications

The Billy Goat KV600SPFB, KV650SPHFB, and TKV650SPHFB are three versatile and powerful leaf vacuums designed for both residential and commercial use. These models stand out in the market due to their robust build quality, high-performance capabilities, and innovative features that meet the needs of landscapers, property managers, and homeowners alike.

Beginning with the KV600SPFB model, it features a powerful 190cc Honda engine, which delivers exceptional performance and reliability. The KV600SPFB is equipped with a self-propelled system that provides ease of use, allowing users to navigate through varying terrains effortlessly. Its generous 27-inch wide vacuum intake allows for swift leaf collection, making it a time-saving tool for large areas. One of the standout features of this model is its unique blower system that enables users to switch from vacuuming to blowing mode seamlessly, enhancing versatility.

Moving on to the KV650SPHFB, this model builds upon the features of the KV600SPFB with an added emphasis on power and efficiency. Featuring a 223cc Honda engine, the KV650SPHFB operates with more power, ensuring the capability to handle dense leaf clusters and debris with ease. This model continues the tradition of self-propelled functionality and boasts a larger 29-inch vacuum intake. It also incorporates a 5-blade impeller system that provides superior shredding capabilities, reducing the volume of debris collected by up to 10:1, which is essential for effective composting or easy disposal.

Lastly, the TKV650SPHFB adds further enhancements tailored for professionals. Besides the robust 223cc engine and 29-inch vacuum intake, the TKV650SPHFB is designed with a detachable debris bag that maximizes capacity and minimizes downtime. This model excels in maneuverability, featuring larger rear wheels and a tighter turn radius. The TKV650SPHFB is not only efficient in collecting leaves but also equipped with a durable build that can withstand heavy use in various environmental conditions.

All three models are designed with user-friendly controls, ensuring that operators of any skill level can use them effectively. Overall, the Billy Goat line of leaf vacuums provides an exceptional combination of power, efficiency, and user-oriented design, making them ideal choices for anyone looking to maintain a clean outdoor environment. Whether for residential use or professional landscaping, these models offer a compelling solution for tackling leaf and debris collection with ease and effectiveness.
Top Page Image Contents