Drive, Maintenance | Billy Goat VQ902SPH, VQ1002SP specs

VQ Owner’s Manual

DRIVE

Chains and Belts are normal replaceable wear items. A new chain should not be used on worn sprockets. Sprockets should be replaced when replacing chains.

MAINTENANCE

Brake Adjustment: As parking brake wears, the brake discs may eventually require adjustment. To adjust belt, remove brake guard and tighten mounting nut that connects brake arm onto transmission. Adjust cable as required. Unit must freewheel with brake off. DO NOT OVER ADJUST.

CHAIN ADJUSTMENTS (see pg. 17)

1.Remove guards and place a support underneath the back end of the machine to raise the back wheels off of the ground.

2.Inspect chain and sprockets for wear, lubrication and tension. Replace if badly worn or damaged.

CHAIN TENSION AND ALIGNMENT (see pg. 17)

3.To install a new chain, locate and remove the keeper clip of chain connecting link on inboard side of chain. Along with the master link and remove the chain. Replace chain, master link and keeper clip. Make sure the open end of the clip is facing away from the chain travel and that the clip is on the inboard side of the unit.

4.Check the alignment of the chain to ensure that the chain will not jump off of the sprockets by rotating the wheels while they are off the ground. If the chain is aligned properly proceed to step 8.

5.Alignment is made by loosening the nuts on the rear wheel bearings, do not remove bearing carriage bolts, nuts or wheels.

6.With the bearings pressed fully outward against wheels, keeping axle square with engine base, align and tension chain for proper travel in as straight of a line as possible. When the desired position is reached, slightly tighten front bearing bolts and nuts first. Then slightly tighten rear bearings. (Note: Tightening the front bearing carriage bolts and nuts first, helps keep chain tight.)

7.Recheck chain alignment, tension and axle squareness. If ok, fully tighten front and then rear bearing screws. Repeat adjustment steps if necessary.

8.Check chain tension and roll wheels to be sure there are no excessively tight areas in the chain. Readjust if necessary.

9.Reinstall chain guard and differential guard.

10.Reinstall spark plug wire.

Belt Adjustment: As V-belt wears, adjustments may be required. Adjust by tightening or by loosening clutch cable nut as required. When replacing the belt, the impeller must be removed. See instructions on page 12. See parts list for impeller bolt torque specifications. See figure 10 & 11 for proper belt tension adjustment. If cable cannot be adjusted to provide proper belt tension then belt must be replaced. DO NOT OVER ADJUST.

Chain Lubrication: With machine not running, oil chain using general S.A.E. 30 weight oil or chain lube every 10 hours or as

needed. Chain oiling hole is located in rear axle cover. Note: Be sure that entire length of chain is properly oiled. Oiling only a few positions in the chain rotation will not properly oil the chain.

Transmission	Idler Pulley
pulley	in Drive
	Position

Belt	Wire	0.06 (1.5mm)
	Belt	0.125 (3.3mm)
	guides
		0.06 (1.5mm)
		0.125 (3.3mm)

Idler Pulley	Pulley
in neutral	turns freely
position

Engaged drive position: Wire belt guides

should clear belt by 0.06” - 0.125”Fig. 10 (1.5mm – 3.3mm

Neutral position

Fig. 11

Part No 830542

Form No F062007A

VQ902SPH, VQ1002SP specifications

The Billy Goat VQ902SPH and VQ1002SP are two powerful and efficient vacuum systems designed for homeowners and professional landscapers alike. These vacuum units are built to cater to outdoor cleanup needs, particularly for leaf collection and debris management, making them essential tools in maintaining a pristine landscape.

One of the standout features of both models is their robust engine. The VQ902SPH is equipped with a 9.0 HP Honda engine, while the VQ1002SP boasts a 10.0 HP engine. These powerful engines deliver impressive suction capabilities, allowing for easy collection of a variety of debris sizes, from leaves and grass clippings to larger twigs. The high-performance engines ensure that users can tackle large areas efficiently without the need for frequent stops.

Both units come with a large, high-capacity debris bag, which minimizes downtime by reducing the frequency of emptying. The VQ902SPH features a 30-bushel capacity, while the VQ1002SP's bag offers even more spacious storage. This means users can collect more debris in one go, making the cleanup process faster and more convenient.

An important consideration in outdoor equipment is maneuverability. Both vacuums incorporate a user-friendly design, featuring large, durable wheels that allow for easy navigation across various terrains. The ergonomic handle design ensures comfortable operation, reducing fatigue during extended use. Additionally, these models include a convenient tow-behind option for those who need to attach them to a tractor or ATV, enhancing versatility.

The innovative Cyclonic Filtration System used in the VQ902SPH and VQ1002SP improves air flow and performance, preventing clogging and allowing for consistent suction power throughout the operation. This tech ensures that dust and debris are collected efficiently without compromising the vacuum's functionality.

Another notable characteristic of both models is their all-steel construction, which provides durability and longevity. Whether encountering rough outdoor environments or consistent use, these vacuums are built to withstand the rigors of outdoor tasks.

In conclusion, the Billy Goat VQ902SPH and VQ1002SP are formidable tools for anyone looking to maintain their outdoor spaces effectively. With powerful engines, large debris capacity, superior maneuverability, and durable construction, these vacuum units deliver excellent performance, making them invaluable for efficient yard maintenance and cleanup.

Billy Goat VQ902SPH, VQ1002SP owner manual Drive, Maintenance

Models: VQ902SPH, VQ1002SP