Assembly, Tighten jam nuts | Billy Goat VQ902SPH, VQ1002SP guide

VQ Owner’s Manual

ASSEMBLY

1. UPPER HANDLE (item 41). Assemble securely to lower handle stubs (item 37) and handle brace (item 36), using screws (item 120 & 121), so that screw heads are on inside of handle. Otherwise, premature bag wear could result.

2. NOZZLE DOOR CONTROLS. Assemble ball joints (item 73), jam nuts (item 138), to both ends of rod (item 47). Do not fully

tighten jam nuts.

Using screw (item 113), washer (item 143) and lock nut (item 131), connect one end of rod (item 47) to nozzle door mounting. (See Figure 5). Using rod, pull nozzle door open horizontal to ground and hold opposite end of rod next to mounting hole on remote lever (item 48), already assembled onto upper handle. (See Figure 1). If necessary, adjust rod length using threads provided on rod. Adjust rod length to give a minimum of 1.0" (25.4 mm) hand clearance between lever & maximum forward throttle position when door is open. Assemble upper end of rod to lever on handle using same hardware item numbers as shown above. (See figure 1& 2). Tighten jam nuts.

3. EXHAUST ASSY. Place flange gasket (item 35) onto housing of main unit and assemble exhaust elbow to housing using screws (item 117), washers (item 140) and lock nuts (item 132), provided in parts bag. The rear hole mounts deflector (item 118), using screw assembly (already attached to deflector) and lock nut (item 132). Bend opposite end of deflector down until notch in rear of deflector catches onto handle brace (item 36) (see figure 3).

4. DEBRIS BAG (Item 50) (see figure 4).

4.1Unfold and place mouth of bag over exhaust elbow, completely covering the discharge opening with bag neck straps, placing one on each side of elbow flange.

COMPLETELY TIGHTEN BAG NECK STRAPS

4.2Attach rear hanger straps of bag to the hanger loops located one on each side of the upper handle.

5. CABLES AND WIRES. Attach to the handle using cable clamps (item 44).

6.Secure engine starter rope into starter rope guide (Item 177) using hardware that is preassembled to the lower handle.

7.INSPECT ALL PARTS & MECHANICAL FASTENERS for security and integrity.

8.Note: See debris bag conditioning under operation section on page 11).

SELF PROPELLED ONLY (before starting unit).

9. CONTROL ASSY (item 77).

Before starting engine, check for neutral by placing the control into neutral and engaging the bail, the unit has been adjusted at the factory and should free wheel. If not, adjust as needed by placing the control (item 77) and transmission offset link (item 68) into neutral and adjust nuts on control cable (item 75).

10.Check tire pressure and lubricate all grease and oil points (see MAINTENANCE).

11.Connect spark plug wire.

138

Fig. 1

138

Fig. 2

118

Deflector notch

Fig. 3

Fig. 4

Fig. 5

Part No 830542

Form No F062007A

VQ902SPH, VQ1002SP specifications

The Billy Goat VQ902SPH and VQ1002SP are two powerful and efficient vacuum systems designed for homeowners and professional landscapers alike. These vacuum units are built to cater to outdoor cleanup needs, particularly for leaf collection and debris management, making them essential tools in maintaining a pristine landscape.

One of the standout features of both models is their robust engine. The VQ902SPH is equipped with a 9.0 HP Honda engine, while the VQ1002SP boasts a 10.0 HP engine. These powerful engines deliver impressive suction capabilities, allowing for easy collection of a variety of debris sizes, from leaves and grass clippings to larger twigs. The high-performance engines ensure that users can tackle large areas efficiently without the need for frequent stops.

Both units come with a large, high-capacity debris bag, which minimizes downtime by reducing the frequency of emptying. The VQ902SPH features a 30-bushel capacity, while the VQ1002SP's bag offers even more spacious storage. This means users can collect more debris in one go, making the cleanup process faster and more convenient.

An important consideration in outdoor equipment is maneuverability. Both vacuums incorporate a user-friendly design, featuring large, durable wheels that allow for easy navigation across various terrains. The ergonomic handle design ensures comfortable operation, reducing fatigue during extended use. Additionally, these models include a convenient tow-behind option for those who need to attach them to a tractor or ATV, enhancing versatility.

The innovative Cyclonic Filtration System used in the VQ902SPH and VQ1002SP improves air flow and performance, preventing clogging and allowing for consistent suction power throughout the operation. This tech ensures that dust and debris are collected efficiently without compromising the vacuum's functionality.

Another notable characteristic of both models is their all-steel construction, which provides durability and longevity. Whether encountering rough outdoor environments or consistent use, these vacuums are built to withstand the rigors of outdoor tasks.

In conclusion, the Billy Goat VQ902SPH and VQ1002SP are formidable tools for anyone looking to maintain their outdoor spaces effectively. With powerful engines, large debris capacity, superior maneuverability, and durable construction, these vacuum units deliver excellent performance, making them invaluable for efficient yard maintenance and cleanup.

Billy Goat VQ902SPH, VQ1002SP owner manual Assembly, Tighten jam nuts

Models: VQ902SPH, VQ1002SP