Bizfon 2000, 4000 Requirements

Bizfon Manual I: Installation Guide Requirements

Requirements

• One 120/240 VAC power outlet in close proximity to the Bizfon.

• One RJ45 Ethernet 10/100 broadband Internet connection.

• At least one RJ11 telephone connection is recommended to connect the Bizfon to the

PSTN network (all Bizfon IP PBXs with FXO ports).

• At least one off-the-shelf analog phone with an RJ11 telephone cable.

• One CAT 5 Ethernet cable with an RJ45 connector to connect to the Bizfon LAN port.

apter installed.

• 5 or higher, or Netscape Navigator 4.7 or

e added according to the different connectivity requirements of the Bizfon IP

PBX types.

• One PC with a 10/100 Mbps Ethernet card or ad

• TCP/IP network protocol installed on each PC.

For optimal results, Internet Explorer 5.

higher are recommended.

Please Note: All Bizfon IP PBXs are shipped with one RJ11 cable and one straight RJ45

CAT 5 cable. If the LAN connector of the Bizfon connects to a hub or switch, a crossover

cable may be required.

Other cables ar

Bizfon2000 and Bizfon4000 (SW Version 3.1.x) 6

Contents

Main Bizfon Manual I: Installation Guide Copyright and Trademarks Limited Warranty Return Policy Notice to Users Bizfon Manual I: Installation Guide S t y Services Table of Contents About This Installation Guide Requirements Hardware Overview The Rear Panels of Bizfon2000 and Bizfon4000 Bizfon Manual I: Installation Guide Hardware Overview Bizfons Front Panel LEDs 1 2 3 Page Step 1: Installing the Bizfon Networking Overview LAN/WAN Connection Options Page Connecting the Hardware Verify the product package contents are complete. Refer to the contents sheet included Before you connect the hardware, make sure that all devices are powered off. Connect the WAN port of the Bizfon to the Power up the DSL or Cable modem first. Step 2: Configuring the Bizfon Bizfon IP PBXs with Ethernet WAN up- link do not require further configuration in two cases: calls allowed by the Bizfon to avoid Enter http://172.30.0.1 (Bizfons default LAN IP address) into the address field. Step 2.2: System Configuration Wizard System Configuration DHCP Settings for the LAN Interface Regional Settings Emergency and PSTN Access Code Settings Finishing the System Configuration Wizard Page Step 2.3: Internet Configuration Wizard MAC address - needed when the ISP requires a specific MAC address for the WAN. PPP Configuration - does your ISP use a dynamic or fixed WAN IP address? If the plink Configuration U AN IP Configuration W Page PPP/PPTP Configuration WAN Interface Configuration DNS Settings Finishing the Internet Configuration Wizard Step 2.4: Firewall Configuration Step 2-A: Using IP Lines Go to Bizfon Status- SIP Registration status Registered IP Lines to see if Dial *74 to get the line information. Make outgoing and accept incoming calls. Step 2-B: Using Receptionist Step 3: Making/Receiving Calls To make a call to the PSTN, lift the handset and dial 9 and the local phone number. To make a VoIP call to a user on the remote Bizfon, lift the handset and dial 8 + SIP Using the Default SIP Addresses Page Appendix: PC DHCP Settings TCP/IP network protocol has to be installed. DHCP has to be activated in order to request the IP address automatically TCP/IP and DHCP under Windows 2000/XP TCP/IP and DHCP under Windows 95/98/ME Appendix: Changing the Admin Password Appendix: Configuring NAT Traversal Install the Bizfon behind the router. If the Bizfon is configured with its factory default Find the address of the router and log into the router. Refer to the routers user manual Go to the RTP Parameters page and select Use Manual NAT Traversal. Enter the WAN IP address of the router into the Mapped Host text field. Set the Appendix: Checking the Connections Unknown connection - unexpected error Symmetric NAT all Symmetric Firew Blocked UDP