and deadly gas.

•DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty.

NOTICE: Risk of property damage. Never pull water supply hose to move pressure­ washer. This could damage hose and/or pump inlet.

•DO NOT use hot water, use cold water only.

•Never turn water supply off while pres- sure washer engine is running or dam- age to pump will result.

•DO NOT stop spraying water for more than two minutes at a time. Pump oper- ates in bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged.

If you do not understand these precau- tions, please call 1-800-544-6986to speak to a service representative for fur- ther instructions.

faces out.

5.Connect water source to pump inlet. NOTE: Water source must provide a minimum of 5 gallons (18.9 liters) per minute at 20 psi (137.9 kPa).

D

Water

Source

WARNING: To reduce the possibil- ity of contamination always protect against backflow when connected to a potable water system.

6.Connect high pressure hose to pump outlet.

7.If applying a chemical or clean- ing solution, see How To Apply

Chemicals/Cleaning Solvents instructions in this section.

8.Turn water source on.

starting

Prior to starting, refer to your engine manual for proper starting procedure.

1.In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to Engine Owners Manual for correct procedure.

2.Check engine oil level. See Engine Owners Manual for correct procedure.

3.Connect the water hose to the water source. Turn the water source on to remove all air from the hose. When a steady stream of water is present, turn the water source off.

NOTICE: Risk of property damage. Failure to do so could cause damage to the pump.

9.Remove all air from the pump and high pressure hose by depressing trigger until a steady stream of water is present.

10.Turn the engine

ON/OFF switch

(H) to the ON position.

11.Place the fuel

valve lever (M) in the ON postion.

12.If the engine is cold, move the choke (L) to the CLOSED position as shown.

4.Verify the filter screen is in water inlet of pump. NOTE: Cone side

12- ENG­

Page 11 Page 13
Page 12
Image 12
Black & Decker BDP2600 Deadly gas, Do not use hot water, use cold water only, Connect high pressure hose to pump outlet
Page 11 Page 13

BDP2600 specifications

The Black & Decker BDP2600 is a versatile and powerful tool that has garnered attention in the realm of home improvement and DIY enthusiasts. This tool is specifically designed to meet the needs of both amateur and professional users, offering a range of features and technologies that enhance its performance and usability.

One of the standout features of the BDP2600 is its powerful motor that delivers high performance for a variety of applications. Whether you're drilling, sanding, or performing other tasks, the motor ensures efficient operation, reducing the time and effort required to complete projects. The tool's design incorporates an ergonomic handle, providing comfort during prolonged use, which is especially important for users engaged in detailed work.

The BDP2600 is equipped with a variable speed control feature, allowing users to adjust the speed according to the task at hand. This flexibility is crucial when dealing with different materials, as it helps achieve optimal results without compromising on safety. Additionally, a built-in safety lock ensures that the tool can only be activated when intended, reducing the risk of accidents.

Another notable technology in the BDP2600 is its durable construction. Built to withstand the rigors of frequent use, this tool features quality materials that contribute to its longevity. The robust design not only enhances durability but also improves reliability, making it a preferred choice for many DIY projects and professional applications alike.

The BDP2600 also offers an array of attachments and accessories, further increasing its versatility. These attachments allow the tool to perform a wide range of functions, from drilling into various surfaces to sanding and polishing. This multifunctionality makes the BDP2600 a valuable addition to any toolkit.

In conclusion, the Black & Decker BDP2600 stands out for its powerful motor, ergonomic design, variable speed control, safety features, and robust construction. With its extensive range of applications and accessories, it is tailored to meet the diverse demands of users. Whether you are tackling small home repairs or larger renovation projects, the BDP2600 is a reliable and efficient tool that facilitates ease and precision in your work. Its blend of innovation and practicality continues to make it a popular choice in the competitive market of power tools.
Top Page Image Contents