Using the Spray Button
Use to dampen tough wrinkles at any setting.
1.Be sure the iron is filled with water.
2.On first use, pump the Spray button 
several times (K).
Ironing without Steam |
• The unit beeps once and the AUTO OFF symbol 
on the LCD display appears to let you know the iron has stopped heating (Q).
Important: Although the iron has turned off, it is still hot.
•After a few seconds, the backlight on the LCD display turns off.
•If you pick up the iron, an internal motion detector is activated
K | 1. Ironing without steam can be performed at any setting. |
|
Q
and the iron starts heating gain.
|
|
| 2. It is not necessary to empty the water tank; simply press the | |
|
| |||
| ACRYL |
| steam button to the OFF position. The steam symbol(s) | |
|
| will disappear from the LCD display (L). | ||
| 1 |
| ||
|
| 3. If desired, empty the water tank following the directions | ||
|
|
| ||
|
|
| below and press the steam button | to turn off the steam. |
| ACRYL |
| VERTICAL STEAM |
|
L | 1 |
| Use for removing wrinkles from hanging garments, curtains and | |
|
| drapes. |
| |
|
|
|
| |
1.Be sure water tank is filled to maximum capacity.
2.Hang garment to be steamed on a clothes hanger. Curtains and drapes can be steamed where they are hung.
3.Press fabric selection button to reach appropriate fabric setting. Allow the iron to stand
for 90 seconds until the Standby 
symbol in the bottom right of the LCD display changes to Ready 
.
Tip: You might have to move the iron or shake it gently.
•The unit beeps once, the digital display light comes on, and the previously set temperature is displayed again.
Note: Wait for iron to reheat completely before resuming operation.
The
AUTO CLEAN® System 
Note: If the AUTO CLEAN® symbol 
appears on the LCD display, the unit needs cleaning. Follow the procedure under AUTO CLEAN® System.
Care and Cleaning
This product contains no
Cleaning Outside Surfaces
M
N
O
30 SECONDS
4.Hold the iron close, but not touching the fabric.
5.Using your free hand, pull the fabric tight and pump the
Emptying the Water Tank (optional)
Note: It is not necessary to empty the water tank after each use.
1.Unplug the iron and let it cool.
2.Open the
3.To release the water, hold the iron over a sink with the tip pointing down. Water will empty out of the
SPECIAL FEATURES
Language Settings
Your iron has a multilingual digital display that lets you select from English, French and Spanish.
To change the language (O):
1.Press and hold the
2.Press the
3.Press the
Note: The languages will change in the order listed above.
3-Way Automatic Shutoff
The automatic shutoff feature in your iron works as follows:
•The iron will shut off after 30 seconds of inactivity if left on its soleplate or tipped over on its side. If left vertically on its heel rest, it will shut off after 8 minutes of inactivity (P).
1.Make sure iron is unplugged and has cooled completely. Wipe the soleplate and outer surfaces with a soft cloth dampened with water. Add mild household detergent. Never use abrasives,
2.After cleaning, steam iron over an old cloth to remove any residue from the steam vents.
AUTO CLEAN® System
To keep the steam vents free of any buildup, follow these instructions about once a month.
1.Fill the water tank well below the MAX line. Plug in the iron.
2.Select fabric temperature setting 6 and stand the iron on its heel rest.
3.Wait for the iron to beep and display temperature number with corresponding fabric.
4.Unplug the iron and hold over a sink with the soleplate facing down.
5.Press and hold the AUTO CLEAN® button. Be careful, as after several seconds, hot water and steam will come out of the steam vents (R). Continue to hold the AUTO CLEAN® button until all the water has emptied. If necessary, rock iron
6.When finished, release the button, stand the iron on its heel
R | rest and plug it in. Heat for about 2 minutes to dry out any | |
remaining water. | ||
|
Storing your Iron
1.Unplug the iron and allow it to cool.
2.Store vertically on its heel to prevent water leaking from the soleplate.
P
8 MINUTES
7 | 8 |
