Black & Decker FSMH16151 manual Carpet refreshing, After use Fig. N & O, Hand held steam cleaning

ENGLISH (Original instructions)

uWhen you have finished using the steam mop, return the handle (10) to the upright position and turn it ‘OFF’ and wait until the steam mop cools down. (approximately five

minutes)

Caution! It is important to monitor the water level in the water tank. To refill the water tank and continue to sanitise/clean, re- turn the handle (10) to the upright position and turn the steam mop ‘OFF’. Unplug the unit from the electrical wall outlet, refill the water tank (8).

Caution! Never leave the steam mop in one spot on any surface for any period of time. Always place the steam mop with the handle (10) in the upright position when stationary and make sure the steam mop is turned off when not in use.

Carpet refreshing

uPlace a cleaning pad (12) on the floor with the ‘hook & loop’ side facing up.

uLightly press the steam mop down onto the cleaning pad

uPlace the carpet glider (14) on the floor.

uLightly press the steam mop down onto the carpet glider

(14)until it clicks into place.

uConnect the steam mop to the mains.

uPress the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.

uPress the AutoselectTM button (6) to the Wood/Laminate setting.

uPulling the handle (10) back will activate the steam pump. After a few seconds steam will start to come out of the steam head.

Note: When first filled or after running dry it can take up to 45 seconds for steam to be produced.

uPush and pull the steam mop slowly across the carpet to thoroughly refresh each section.

Note: During use you may turn off the steam pump by return- ing the handle to the upright position, this convenient feature will allow you to leave the steam mop for a short time so that you may move items of furniture, then continue cleaning without the need to switch the appliance off.

uWhen you have finished using the steam mop, return the handle (10) to the upright position and turn it ‘OFF’ and wait until the steam mop cools down. (approximately five minutes)

Caution! If steam is observed escaping from the join between the hand held steam cleaner and the steam mop body, switch off and disconnect the unit from the mains supply. Allow to cool. Remove the hand held steam cleaner from the steam mop body. Inspect the seal (26) on the steam nozzle (4) and hose (27) (fig. K). If the seal is missing or damaged then please contact your nearest authorised repair agent. Do not use the appliance. If the seal is in good condition re-fit the hand held steam cleaner to the steam mop body ensuring that it is seated firmly in place.

8

Caution! It is important to monitor the water level in the water tank. To refill the water tank and continue to sanitise/clean, re- turn the handle (10) to the upright position and turn the steam mop ‘OFF’. Unplug the unit from the electrical wall outlet, refill the water tank (8).

Caution! Never leave the steam mop in one spot on any surface for any period of time. Always place the steam mop with the handle (10) in the upright position when stationary and make sure the steam mop is turned off when not in use.

After use (Fig. N & O)

uReturn the handle (10) to the upright position and turn the steam mop ‘OFF’,

uWait until the steam mop cools down. (approximately five minutes)

uUnplug the steam mop from the electrical wall outlet.

uEmpty the water tank (8).

uRemove the cleaning pad (12) and wash it ready for next use. (Take care to follow the wash care instructions printed on the cleaning pad).

uWrap the supply cable around the cable tidy hooks (15 & 16).

Note: The top cable tidy hook (16) rotates to easily release the cable ready for next use.

uClip the supply cable onto itself using the cable tidy clip (32) close to the plug.

Note: With the handle (10) in the upright position, the cable neatly wrapped around the cable tidy hooks (15 & 16) and secured with the cable tidy clip (32) your steam mop will stand on its own for storage. Alternatively there is a hanging bracket

(33)built into the hand grip (34) which will allow your steam mop to be hung from a suitable hook on the wall. Always ensure that your wall hook is capable of supporting the weight of the steam mop safely.

Hand held steam cleaning

uAttach the required accessory.

uConnect the hand held steam cleaner to the mains.

uPress the ON/OFF button (1). It takes approximately 15 seconds for the hand held steam cleaner to heat up.

uLift the lock off (2) and pull the trigger switch (3) to activate the steam pump. After a few seconds steam will start to come out of the accessory.

Note: When first filled or after running dry it can take up to 45 seconds for steam to be produced.

Note: During use you may turn off the steam pump by releas- ing the trigger switch, this convenient feature will allow you to place the hand held steam cleaner down for a short time so that you may move items of furniture, then continue cleaning without the need to switch the appliance off.