![](/images/new-backgrounds/1042312/423129x1.webp)
Intended use
Your BLACK+DECKER steam mop has been designed for sanitising and cleaning sealed hardwood, sealed laminate, linoleum, vinyl, ceramic tile, stone and marble floors and for refreshing carpets. This appliance is intended for indoor household use only.
Warning! Read all of the 'Safety, Maintenance, Service' manual carefully before operating this appliance.
Read all of this manual carefully before operating the appliance.
Features
This appliance includes some or all of the following features.
1.ON/Off switch
2.Lock off button
3.Trigger switch
4.Steam nozzle
5.Hand held steam cleaner
6.AutoselectTM button
7.Filler cap
8.Water tank
9.Steam mop body
10.Handle
11.Steam head
12.Steam head cleaning pad
14.Carpet glider
15.Bottom cable tidy hook
16.Top cable tidy hook
17.Cable management clip
Assembly
Warning! Before attempting any of the following operations, make sure that the appliance is switched off and unplugged and that the appliance is cold and does not contain any water.
Attaching the handle (Fig. A)
uSlide the bottom end of the handle (10) into the top end of the steam mop body (9) until it clicks into place. The arrow on the handle (10) should be aligned with the top of the steam mop body (9).
Attaching the steam head (Fig. B)
uSlide the bottom end of the steam mop body (9) onto the steam head (11) until it clicks into place.
uThe steam head can be removed from the Steam mop body by pressing the steam head release button (19) and pulling the steam mop body (9) off the steam head (11).
(Original instructions) | ENGLISH |
Attaching the hand held steam cleaner (Fig. C)
uHolding the back of the steam mop body (9) Push the hand held steam cleaner (5) firmly into the steam mop body (9) until it clicks into place.
Caution! Always ensure the handle command lights up to confirm the unit is docked.
Warning! Inspect that the seal (26 Fig. J) on the steam nozzle
(4)before fitting the hand held steam mop to the steam mop body. If the seal is missing or damaged then please contact your nearest authorised repair agent. Do not use the appli- ance.
Removing the hand held steam cleaner (Fig. C)
uPush the release button (20) down and pull the hand held steam cleaner (5) away from the steam mop body
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your BLACK+DECKER dealer:
Steam head cleaning pad (12) - cat. no.
uPlace a cleaning pad (12) on the floor with the ‘hook & loop’ side facing up.
uLightly press the steam mop down onto the cleaning pad (12).
Caution! Always place your steam mop with the handle (10) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the cleaning pad on your steam mop. Do not wear slippers or open toed footwear.
uReturn the handle (10) to the upright position and turn the steam mop ‘OFF’.
uWait until the steam mop cools down. (approximately five minutes)
uPlace the front of your shoe onto the cleaning pad removal tab (21) and press down firmly.
uLift the steam mop up off the cleaning pad.
Caution! Always place your steam mop with the handle (10) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Filling the water tank (Fig. F)
This Steam cleaner incorporates an
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of
uOpen the filler cap (7) by flipping it down.
uFill the water tank (8) with water.
Warning! Your water tank has a 0.36 litre capacity.
u
5