Black & Decker 90518305 Detail Sanding, Fitting Sanding Sheets Fig, Tip of the Sanding Base Fig

90518305 03 MS600 ZONE MOUSE:??????-00 BDL500 laser 12/11/09 10:51 AM Page 8

ZONE 2

Displays when:

• Optimum pressure is being applied to achieve optimum performance and low fatigue.

Zone Lens will illuminate a high intensity green light which will appear all across the Zone Indicator (“U” display).

ZONE 3

Displays when:

• Too much pressure is being applied.

Zone Lens will illuminate a red light which will appear in the center of the Zone Indicator (“U” display).

NOTE: Excessive pressure may result in harming or causing divots in the surface you are sanding.

Detail Sanding

WARNING: Always unplug product from power supply before any of the following operations.

Your tool is equipped with a teardrop base which allows you to use it on large flat surfaces and tight spots or corners.

The pad tips may wear unevenly, depending on use. The pads are designed to allow you to interchange and /or rotate the diamond tip.

Fitting Sanding Sheets ( Fig. 2)

•Detach the two diamond-shaped tips from the sanding sheet.

•Hold the tool with the sanding base facing upwards.

•Place the sanding sheet onto the sanding base.

The diamond-shaped tip can be reversed and replaced when worn.

•When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto the sanding base again.

•When the whole tip is worn, remove it from the sanding base and fit a new tip.

Tip of the Sanding Base ( Fig. 3)

When the sanding base tip is worn, it can be reversed or replaced.

• Reverse or replace the worn part.

Finger Attachment ( Fig. 4)

The finger attachment is used for fine detail sanding.

•Remove the screw.

•Remove the diamond-shaped tip holder from the sanding base.

•Fit the finger attachment onto the sanding base.

•Fit and tighten the screw.

•Align the sanding sheet with the finger attachment.

Contour Holder Attachment (Fig. 5)

•The contour sanding pieces are for sanding curved surfaces and grooves.

•Remove the screw.

•Remove the diamond-shaped tip holder from the sanding base.

•Fit the contour holder onto the sanding base.

•Fit and tighten the screw.

Fitting and Removing a Contour Piece (Fig. 6 & 7)

•Choose the contour sanding piece profile most suitable for your application.

•Place one end of the contour sanding piece into the recess at the front end of the contour holder.

•Push the other end of the contour sanding piece until it clicks into place.

•To remove the contour sanding piece, push it forward then pull the rear end out of the contour holder (fig. 7).

8

Fitting a Sanding Sheet Onto a Contour Sanding Piece (Fig. 8)

•Align the sanding sheet with the contour sanding piece.

•Press the sanding sheet onto the contour sanding piece, making sure that the sanding sheet follows the shape of the profile.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

Accessories

Look for the following MouseTM accessories at your local retailer.

Catalog #	Description	Contents
74-583	120 Medium Sandpaper	5 sheets
74-584	180 Fine Sandpaper	5 sheets
74-585	220 Extra Fine Sandpaper	5 sheets
74-586	Sandpaper Assortment	1 sheet of 120 grit paper, 2 sheets each 180,
		220 paper
74-587	Finger Attachment Paper	5 fingers each of 120, 180, 220
74-588	1 OT Power Wool	3 sheets
74-589	4 OT Power Wool	3 sheets
74-581	Polishing Kit	2 sheets of 1 OT power wool, 2 sheets of 4 OT
		power wool, 2 foam pads
74-582	Scrubbing Kit	2 coarse abrasive pads, 2 fine abrasive pads,
		2 foam pads
74-580	Sanding/Polishing Kit	2 sheets of 1 OT power wool, 2 sheets of 180
		grit sandpaper, 2 sheets of 240 grit sandpaper,
		2 foam pads, 5 finger attachment paper
74-671	Universal Sandpaper/Coarse 5 sheets of 80 grit
74-672	Universal Sandpaper/Med.	5 sheets of 120 grit
74-673	Universal Sandpaper/Fine	5 sheets of 220 grit
74-674	Universal Sandpaper	Assortment

Recommended accessories for use with your tool are available at extra cost. Listings per retailer may vary. The hook and loop pad and individual bases are replaceable parts. If they become worn, contact your local service center. For more information call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

Application / Accessory Matrix

ACCESSORY	RECOMMENDED APPLICATIONS / USES
MEDIUM GRIT SANDPAPER	PAINT, VARNISH, RUST REMOVAL
FINE GRIT SANDPAPER	SURFACE BLENDING AND FINISHING
EXTRA FINE GRIT SANDPAPER	SANDING BETWEEN COATS OF PAINT OR VARNISH
DETAIL SANDING TIPS	CORNERS / HARD TO REACH PLACES
1 OT POLISHING / STRIPPING WOOL POLISHING METALS / STRIPPING VARNISH OR URETHANE
4 OT FINE POLISHING WOOL	FINE POLISHING, SATIN FINISH ON PAINT / VARNISH / URETHANE
GREY FOAM PAD	APPLYING AND REMOVING POLISH
WHITE NON-WOVEN PAD	LIGHT SCRUBBING
RED NON-WOVEN PAD	HEAVY SCRUBBING / RUST REMOVAL

The pads described above are available in kits where Mouse products are sold, The hook and loop pad and individual bases are replaceable parts. If they become worn, contact your local service center. For more information call 1-800-544-6986.

9