90563738 NST1024.qxd: chainsaw booklet new 5/25/10 1:13 PM Page 14
TROUBLESHOOTING
Problem | Possible Cause |
| Possible Solution | ||||||
• Line wonʼt feed. | • Line tangled in spool. |
| • Unwrap line and rewind. | ||||||
• Line fails to cut off. | • Line cutter in guard is damaged or missing. | • Return to service center for repair. | |||||||
| • Line extends past guard. |
| • Rewind or trim line to line cutter. | ||||||
• Unit will not start. | • Battery not installed properly. |
| • Check battery installation. |
|
|
| |||
| • Battery not charged. |
| • Check battery charging requirements. | ||||||
| • Trigger lock off not pressed |
| • Press trigger lock in. | ||||||
• Battery wonʼt charge. | • Battery not inserted into charger. |
| • Insert battery into charger until green LED appears. |
| |||||
| • Charger not plugged in. |
| • Plug charger into a working outlet. Refer to | ||||||
|
|
| “Important Charging Notes” for more details. | ||||||
|
|
| • Check current at receptacle by plugging in a | ||||||
|
|
| lamp or other appliance. | ||||||
|
|
| • Check to see if receptacle is connected to a | ||||||
|
|
| light switch which turns power off when you turn | ||||||
|
|
| out the lights. | ||||||
| • Surrounding air temperature too hot or too cold. | • Move charger and tool to a surrounding air | |||||||
|
|
| temperature of above 40 degree F (4.5°C) or | ||||||
|
|
| below 105 degree F (+40.5°C). | ||||||
• Trimmer / Battery has low | • Battery not charged full 9 hours. |
| • Charge battery for full 9 hours or until the |
| |||||
runtime. |
|
| green LED charging light goes out. | ||||||
| • Additional battery needed. |
| • Contact your local Black & Decker retailer, | ||||||
|
|
| service center or call | ||||||
|
|
| assistance in obtaining accessories. | ||||||
|
|
|
|
|
|
|
| ||
For assistance, visit our website | www.blackanddecker.com for the location of the service center nearest you or call the | ||||||||
BLACK & DECKER help line at |
|
|
|
|
|
|
|
| |
| Imported by |
|
|
|
|
|
|
|
|
| Black & Decker (U.S.) Inc., | See |
|
|
|
| |||
| 701 E. Joppa Rd. | – Yellow Pages – |
|
|
|
| |||
| Towson, MD 21286 U.S.A. | for Service & Sales |
|
|
|
| |||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
BORDURE - MODE DʼEMPLOI
Merci d’avoir choisi Black & Decker!
Consulter le site Web
www.BlackandDecker.com/NewOwner pour enregistrer votre nouveau produit.
ALIRE AVANT DE RETOURNER CE PRODUIT POUR QUELQUE RAISON QUE CE SOIT :
Si des questions ou des problèmes surgissent après l’achat d’un produit
Black & Decker, consulter le site Web
HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS
pour obtenir des réponses instantanément 24 heures par jour.
Si la réponse est introuvable ou en l’absence d’accès à Internet,
composer le
pour parler avec un agent.
Prière d’avoir le numéro de catalogue sous la main lors de l’appel.
CONSERVER CE MANUEL POUR UN USAGE ULTERIEUR.VOICI DES RENSEIGNEMENTS IMPORTANTS A
CONNAITRE :
•Le
•Pour faire fonctionner le
•Il sʼagit dʼun
•Utiliser uniquement un fil de 1,65 mm (0,065 po) de diamètre. Pour obtenir des résultats optimaux, utiliser une bobine préparée
en usine de Black & Decker, nº de catalogue
• Installer le dispositif de protection et la poignée auxiliaire.
• Tournevis à pointe cruciforme requis (non fourni) pour installer un
• Pour obtenir une alimentation du fil sans tracas et des résultats optimaux, utiliser uniquement les bobines de rechange Black & Decker pourvues dʼun fil unique de 1,65 mm (0,065 po). Le numéro de modèle de la bobine de rechange Black & Decker est
14 |
15