Black & Decker PW1300TDW instruction manual Maintenance

18 • ENGLISH

Use of extension cables: Use cables featuring “IPX5” protection level. The cross-section of the extension cable should be proportionate to its length; the longer it is, the greater its cross-section should be. See Fig. G.

Water supply connection

Caution! Only clean or teredwater should be used for intake. The delivery of the water intake tap should be equal to that of pump capacity. Place the appliance as close to the water supply system as possible.

Connection points:

Water outlet (OUTLET)

Water inlet with filter (INLET)

Connection to the mains water supply

The appliance can be connected directly to the mains drinking water supply only if the supply hose is fitted with a backflow preventer valve as per current regulations in force. Make sure that the hose is at least Ø13mm and that it is reinforced.

Connecting to the mains water system/water supply

Detergent flow is adjusted using the regulator.

Warning! Comply strictly with the technical regulations and standards of the local water supply company.

ff Ensure that the water mains connection complies with the data provided in the appliance’s technical specifications.

ff Connect the water supply hose (not supplied) to the appliance’s intake connection (Fig. C).

ff Turn on the water supply.

ff Vent the air from the appliance. To vent the air from the appliance, set the nozzle in low pressure mode (Fully forward) and press the trigger (First releasing the safety catch (10) if necessary) until the water which flows out is free from air bubbles. When done, return the nozzle to the high pressure setting.

appliance without water will damage it; do not cover the ventilation grilles when the appliance is in use.

1.Turn on the water supply tap fully.

2.Release the safety catch (10).

3.Depress the gun trigger for a few seconds and start up the appliance using the starter device (ON/I)(12a).

AS Models - In AS models with automatic delivery flow cut-o system:

a.When the gun trigger is released the dynamic pressure automatically cuts out the motor;

b.When the gun trigger is depressed the automatic drop in pressure starts the motor and the pressure is restored after a very slight delay;

c.If the AS is to function correctly all gun releasing and depressing operations must be performed at intervals of less than 4 - 5 seconds.

Note: To prevent damage to the appliance, when running do not stop the water jet for more than 10 minutes at a time.

Stopping the appliance (Fig. E)

1.Set the starter device switch on (OFF/0)(12b).

2.Depress the gun trigger and discharge the residual pressure inside the hoses.

3.Engage the gun safety catch (10).

Restarting

1.Release the safety catch (10).

2.Depress the gun trigger and discharge the residual air inside the hoses.

3.Set the starter device on (ON/I)(12a).

Storage

1.Switch the appliance off (OFF/0)(12b).

2.Remove the plug from the socket.

3.Turn o the water supply tap.

4.Discharge the residual pressure from the gun until all the water has come out of the nozzle.

5.Engage the gun safety catch (10).

USE OF THE APPLIANCE (Fig. E)

Starter device (12)

Set the starter switch on (ON/I) (12a) to:

a.Start the motor (In models without AS device);

b.Set the motor ready to start (In models with AS device). Note: If there is a pilot light on the starter device, it should light up.

Caution! During operation the appliance must be positioned as shown in Fig. E on a sturdy, stable surface.

Start-up (Fig. E)

MAINTENANCE

Important! To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

Caution! Always disconnect the plug from the power socket before carrying out any work on the appliance.

Cleaning the nozzle (Fig. F)

1.Disconnect the lance from the nozzle.

2.Remove any dirt deposits from the nozzle hole using

Caution! Before starting up the appliance check that	the tool (11).
the water supply hose is connected properly; use of the