1
SAFETY INSTRUCT IONS
1.1 The appliance you have purchased is a technologically advanced
product designed by one of the leading European manufacturers
of high pressure pumps. To obtain the best performance from your
unit, read this booklet carefully and follow the instructions each
time you use it. We congratulate you on your choice and wish you
successful operation.
2
SAFETY RULES
2.1 SAFETY “MUST NOTS”
2.1.1 DO NOT use the appliance with
inammable or toxic liquids, or
any products which are not compatible with the correct operation
of the appliance. EXPLOSIONOR POISONING HAZARD
2.1.2 DO NOT direct the water jet towards people or
animals. INJURYHAZARD
2.1.3 DO NOT direct the water jet towards the unit
itself, electrical parts or towards other electrical
equipment. ELECTRICSHOCK HAZARD
2.1.4 DONOT use the appliance outdoors in case of rain. SHORT
CIRCUITHAZARD
2.1.5 DONOT allow children or incompetent persons to use the
appliance. INJURYHAZARD
2.1.6 DO NOT touch the plug and/or socket with wet
hands. ELECTRICSHOCK HAZARD
2.1.7 DONOT use the appliance if the electrical cable is
damaged. ELECTRICSHOCK AND SHORT CIRCUIT HAZARD
2.1.8 DO NOT use the appliance if the high pressure
hose is damaged. EXPLOSIONHAZARD
2.1.9 DONOT jam the trigger in the operating position. ACCIDENT
HAZARD
2.1.10 Check that the data plates are axed to the appliance, if
not, inform your dealer. Units without plates must NOT
be used as they are unidentiable and potentially dangerous.
ACCIDENTHAZARD
2.1.11 DONOT tamper with or alter the calibration of the
safety valve. EXPLOSIONHAZARD
2.1.12 DO NOT alter the original diameter of the spray head
nozzle. HAZARDOUSALTERATION OF OPERATING PERFORMANCE
2.1.13 DONOT leave the appliance unattended. ACCIDENTHAZARD
2.1.14 DO NOT move the appli ance by pulling on the
ELECTRICAL CABLE.SHORT CIRCUIT HAZARD
2.1.15 Make sure that cars do not drive over the high pressure hose.
2.2 SAFETY “MUSTS”
2.2.1 All electrical conductors MUST BE PROTECTED against the
water jet. SHORTCIRCUIT HAZARD
2.2.2 The appliance MUST ONLY BE CONNECTED to an
adequate power supply in compliance with all
applicable regulations. ELECTRICSHOCK HAZARD
• Use of a safety residual current circuit-breaker (R.C.C.B.) will
provide additional protection for the operator (30 mA).
2.2.3 The high pressure may c ause
materials to bounce o surfaces
at speed; therefore protective clothing and safety goggles MU ST
BE WORN.INJURY HAZARD
2.2.4 Before doing work on the appliance, REMOVE the plug.
ACCIDENTALSTART-UP HAZARD
2.2.5 Before pressing the trigger, GRIP the gun rmly to
counteract the recoil. INJURYHAZARD
2.2.6 COMPLYWITH the requirements of the local water supply
company. According to DIN 1988, the appliance may only
be connected to the mains drinking water supply if a backow
preventer valve with drain facility is installed in the supply hose.
CONTAMINATIONHAZARD
2.2.7
ACCIDENTHAZARD
2.2.8 DISCHARGE residual pressure before disconnecting the
unit hose. INJURYHAZARD
2.2.9 Before using the appliance, CHECK every time that the
screws are fully tightened and that there are no broken or
worn parts. ACCIDENTHAZARD
2.2.10 ONLY USE detergents which will
not corrode the coating materials
of the high pressure hose/electrical cable. EXPLOSION AND ELECTRIC
SHOCKHAZARD
2.2.11 ENSURE that all people or animals keep a minimum
distance of 16 yd. (15m) away. INJURYHAZARD
READ INSTRUCTION MANUAL
BEFORE USE
Maintenance and/or repair of electrical components
MUST be carried out by qualied and authorized
Black & Decker sta for the warranty to take eect.
If the supply cord is damaged, it must be replaced by the
manufacturer, an authorized Black & Decker Service
Centre or an equally qualied person in order to avoid a
hazard. If the supply cord is replaced by an equally
qualied person, but not authorized by Black & Decker,
the warranty will lose eect.
17English