Blanco BFDW8 manual PTroubleshooting,ésentati n de votrewhatlaveto do?-vaisselle

PTroubleshooting,ésentati n de votrewhatlaveto do?-vaisselle

Programming, display anomalies		Possible causes	What to do
The lights light up one		- Wrongly programmed.	- Cancel the current pro-
after another			gramme by holding
			down the “Start” button
			for 2 seconds and then
			reprogramme.
The Salt light does not go	- No salt or too little salt		- Fill the reservoir and
out		in the reservoir to trig-	wait until the cycle
		ger the float.	ends. If the water is
			soft enough not to
			require salt, the Salt
			light is permanently lit.
Poor operation		Possible causes	What to do
The machine cuts off		- Insufficient amperage to	- Check the plug’s ampe-
		supply all the equip-	rage (10A minimum)
		ment being used at the	and the meter’s capacity
		same time.
		- Internal fault in the	- Call a service agent.
		machine
The machine will not		- No power supply to the	- Check the socket and
start		socket	the fuse
		- The tap is closed	- Check that the tap is
			open
		- The water supply hose	- Check that the hose
		is kinked	runs correctly behind
		- Programme selection	the machine
		error and programme	- Cancel by pressing
		blocked	“Start” for 2 seconds
		- “Start” button held down	and reprogramme
		too long (> 2 seconds)	- Press “Start” only briefly
		- Safety system (anti-leak)	to start the programme
			- Call a service agent.
The machine does not		- Protective cover on the	- Remove the protective
drain.		sink’s U bend not removed	cover
		- Drainage hose kinked	- Check the hose runs cor-
			rectly behind the machine
		- Drain filter totally	- Remove the filters and
		blocked	clean. Also clean the
			drain hole.
			- Start a soak programme.
		- Pump blocked.	If the fault persists, call
			a service agent.
22

PTroubleshooting,ésentati n de votrewhatlaveto do?-vaisselle

Poor operation	Possible causes	What to do
A lot of residue left on	- The drain hole and the	- Remove the filters and
the main filter at the end	filters are blocked by	clean them and the drain
of the cycle.	too much residue.	hole. Remove any large
		amounts of residue from
		the plates before placing
		them in the dishwasher.
Steam appears approx.	- The steam from drying	- A normal but infrequent
20 minutes before the	is in contact with a flow	occurrence only when
end of the cycle (model	of cold air.	drying starts (connec-
with ventilated drying).		ted with the temperatu-
		re of the room,
		draughts, etc.).
Poor washing results	Possible causes	What to do
Traces of food, deposits,	- The washing up has	- Arrange the items cor-
“grains of sand” in the	been badly arranged	rectly; use the most sui-
glasses.	(items masked by	table areas and acces-
	another, larger item or	sories for each type of
	placed under it, items	item (see Operating
	side by side or nesting	Instructions).
	together).	- Check that the agitator
	- The upper agitator is	rotates freely (sizing
	blocked by cutlery,	wire), set the basket to
	plates, etc.)	the High position if nec-
	- The filter is not screwed	essary.
	in tightly and is lifting	- Check the seating and
	during washing	the tightness of the fil-
	- The micro-filter’s sieve	ter (screw it in fully to
	is clogged.	the right).
		- Remove and clean all the
		filters (with warm water),
		including the sieve.
Greasy marks.	- Too little detergent,	- Increase the amount of
	poor detergent, stale	detergent; try another
	detergent.	detergent.
	- Unsuitable programme	- Select a programme
	(temperature too low,	with a higher tempera-
	not long enough).	ture.

23