Contact 1.800.762.1142 for assistance. Do not return to place of purchase. | page no. |
9 | |
For great recipes and tips, visit recipes.uniflame.com |
|
|
|
To operate you will need (1)
Note: An empty standard grill LP gas tank weighs approximately 18 lbs. A
Caution: LP gas tank must be properly disconnected and removed prior to moving this grill.
Place precision filled LP gas tank upright into notches on lower right cart frame support so the tank valve is facing the gas line connection.
Burner Connections
1.Make sure the regulator valve and hose connections are securely fastened to the burner and the tank.
If your unit was assembled for you, visually check the connection between the burner venturi pipe and orifice. Make sure the burner venturi pipe fits over the orifice.
WARNING: Failure to inspect this connection or follow these instructions could cause a fire or an explosion which can cause death, serious bodily injury or damage to property.
2.Please refer to diagram for proper installation. (Figures 1 and 2)
3.If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for assistance.
| Figure 1 |
LP Gas Valve | Burner |
with Orifice | venturi |
| pipe |
|
| LP Gas |
| Main Burners | Connection |
|
| |
| Figure 2 |
|
LP Gas Valve |
| LP Gas |
with Orifice |
| Connection |
Secure tank by sliding LP gas tank retainer wire over shoulder of LP gas tank.
Tank/Gas Line Connection
1.Make
2.Make sure control knobs are 
(OFF) position. (Figure 3)
3.Turn LP gas tank valve to “OPEN”.
4.Spoon leak check solution at all “X” locations (Figures 1, 2 and 4)
a.If any bubbles appear turn LP gas tank valve to “CLOSED”, reconnect and
b.If you continue to see bubbles after several attempts, turn LP gas tank valve to “CLOSED” and disconnect LP gas tank and contact 1.800.762.1142 for assistance.
c.If no bubbles appear after one minute turn LP gas tank valve to “CLOSED”, wipe away solution and proceed.
Operating Main BurnersBurner
Side Burnerventuri pipe
Figure 3
First Use
1. | Make sure all labels, packaging and protective films |
| have been removed from the grill. |
2. | Remove manufacturing oils before cooking on this |
| grill for the first time by operating the grill for at |
Figure 4
least 15 minutes on “HIGH” with the lid closed. This |
will “heat clean” the internal parts and dissipate |
odors. |
Lighting
X
X X
X X
Before connecting, be sure that there is no debris caught in the head of the LP gas tank, head of the regulator valve or in the head of the burner and burner ports.
Connect gas line to tank by turning knob clockwise until it stops.
Disconnect LP Gas TankBefore disconnecting make sure the LP gas tank valve is “CLOSED”.
Disconnect gas line from LP gas tank by turning knob counterclockwise until it is loose.
Caution: LP gas tank must be properly disconnected and removed prior to moving this grill.
1.Open lid. Attempting to light the burners with the lid closed may cause an explosion!
2.Make sure there are no obstructions of airflow to the burners. Spiders and insects can nest within and clog the burner / venturi tube at the orifice. A clogged burner tube can lead to a fire beneath the appliance.
3.All control knobs must be in the 
(OFF) position. (Figure 3)
4.Turn LP gas tank valve to “OPEN”.
5.Select burner to light. Push and turn control knob to
(HIGH).
6.Press the 
(electronic igniter) button and hold for up to 5 seconds to light burner.
7.If ignition does not occur in 5 seconds, turn burner
control knob 
(OFF), wait 5 minutes and repeat lighting procedure.
8.If igniter does not light burner, use a lit match secured with the lighting rod provided to light burners manually. Position the lit match near side of the burner. (Figure 5)
Figure 5
Figure 6
FlameSlight Yellow
Slight
Important: Always use the lighting rod provided when
Burner
Blue
Need a tank of gas? Try tank exchange service. It’s easy, fast, safe, and available at tens of thousands of conveniently located retail outlets nationwide. You can purchase a new full tank or exchange your empty for a precision filled one.
lighting burners with a match.
9.After lighting, observe the burner flame, make sure all burner ports are lit and flame height matches illustration. (Figure 6)
Note: Each burner lights independently - repeat steps
Dark Blue